Abstract
The accuracy of stateoftheart atomic clocks is derived from the insensitivity of narrow optical atomic resonances to environmental perturbations. Two such resonances in singly ionized lutetium have been identified with potentially lower sensitivities compared to other clock candidates. Here we report measurement of the most significant unknown atomic property of both transitions, the static differential scalar polarizability. From this, the fractional blackbody radiation shift for one of the transitions is found to be −1.36(9) × 10^{−18} at 300 K, the lowest of any established optical atomic clock. In consideration of leading systematic effects common to all ion clocks, both transitions compare favorably to the most accurate ionbased clocks reported to date. This work firmly establishes Lu^{+} as a promising candidate for a future generation of more accurate optical atomic clocks.
Introduction
Development of stable and accurate time standards has historically been an important driver of both fundamental science and applied technologies. The recent decade has seen phenomenal progress in atomic clocks based on optical transitions such that several systems now demonstrate frequency inaccuracies approaching 10^{−18}^{1,2,3}, two orders of magnitude better than stateoftheart cesium fountain clocks that currently define the SI second^{4}. Redefinition of the second is already under consideration^{5,6}, but is unlikely until consensus on a best optical standard emerges. A significant technical hurdle for achieving inaccuracies below 10^{−18} outside of a cryogenic environment is the systematic uncertainty due to the blackbody radiation (BBR) shift^{7}.
For an optical transition with static differential scalar polarizability Δα_{0} ≡ α_{0}(e) − α_{0}(g), where e and g refer to the excited and ground states respectively, the BBR shift, δν_{bbr}, in Hz, is given by^{8}
Here \(\left\langle {E^2\left( {T_0} \right)} \right\rangle\) = (831.945 V m^{−1})^{2} is the meansquared electric field inside a blackbody at temperature T_{0} = 300 K, and η(T) is a temperature dependant correction which accounts for the frequency dependence of Δα_{0}(ν) over the blackbody spectrum^{8}. Polarizabilities are reported in atomic units throughout which can be converted to SI units via α/h (Hz m^{2} V^{−2}) = 2.48832 × 10^{−8}α (a.u.).
Singly ionized lutetium has two candidate clock transitions with favorable clock systematics^{9,10}, ^{1}S_{0} ↔ ^{3}D_{1} and ^{1}S_{0} ↔ ^{3}D_{2}. Theoretical estimates of Δα_{0,1} ≡ α_{0}(^{3}D_{1}) − α_{0}(^{1}S_{0}) = 0.5(2.7) a.u. and Δα_{0,2} ≡ α_{0}(^{3}D_{2}) − α_{0}(^{1}S_{0}) = −0.9(2.9) a.u. have been given^{11,12}, albeit with indeterminate sign and magnitudes limited by the error estimates. In this work, experimental measurements of both Δα_{0,1} and Δα_{0,2} are made and the BBR shifts assessed. At 300 K, the fractional BBR shifts are −1.36(9) × 10^{−18} and 2.70(21) × 10^{−17} for the ^{1}S_{0} ↔ ^{3}D_{1} and ^{1}S_{0} ↔ ^{3}D_{2} transitions, respectively. The former is the lowest among all optical clock candidates under active consideration^{13}. Finally, the prospects for ^{176}Lu^{+} as a frequency standard are discussed by comparison of its atomic properties to other leading clock candidates.
Results
Measurement methodology
While neutralatom clocks have performed high accuracy (2 × 10^{−5}) measurements of Δα_{0} using precise dc electric fields^{14,15}, this technique cannot be applied for ion clocks. Ion clocks have employed various methods to determine Δα_{0}: inference from micromotioninduced stark shifts^{16}, cancellation of secondorder Doppler and Stark micromotion shifts for cases where Δα_{0} < 0^{17}, and extrapolation from measurements of Δα_{0}(ν) at near infrared (NIR) laser frequencies^{2,18}. These approaches are not suitable for measurements in ^{176}Lu^{+} because, respectively: micromotioninduced Stark shifts would likely be too small to measure accurately, the signs of Δα_{0,1} and Δα_{0,2} are unknown, and extrapolation from measurements at NIR frequencies would be inconclusive given the magnitude of dynamic variation of the polarizabilties^{11}.
The approach taken here is to measure Δα_{0}(ν_{m}) at the midinfrared frequency of ν_{m} = c/(10.6 μm), which is near to the peak of the blackbody spectrum at room temperature. The availability of high power CO_{2} laser sources ensures measurable ac Stark shifts even for small polarizabilities. In addition, a differential measurement of the clock frequency using an interleaved servo technique^{19} requires only one clock and eliminates uncertainties due to commonmode perturbations. This approach enables unambiguous measurement of the sign and magnitude of the polarizabilities with an accuracy limited by the determination of the CO_{2} laser intensity at the ion.
For linearly polarized light of frequency ν, the ac Stark shift of a state ^{3}D_{ J }, F, m_{ F }〉 is given by^{20,21}
where \(C_{F,m_F}\) is a state dependant scale factor^{21}, α_{0,J}(ν) and α_{2,J}(ν) are, respectively, the dynamic scalar and tensor polarizabilities, \(\left\langle {E^2} \right\rangle\) is the mean squared electric field averaged over one optical cycle, and ϕ is the angle between the polarization and quantization axes. The quantization axis is defined by an applied magnetic field of ~ 0.2 mT and different values of ϕ are obtained by rotating this field with respect to the CO_{2} laser polarization. Light shifts as a function of beam position are used to characterize the beam profile and hence intensity for a given power. Light shifts at different values of ϕ for the transitions shown in Fig. 1b, are then used to determine differential scalar polarizabilities, Δα_{0,J}, and tensor polarizabilities α_{2,J} for the two clock transitions.
Experiment description
The experimental setup consists of a single ^{176}Lu^{+} ion confined to a linear Paul trap with identical construction as in ref.^{22}. The trap is operated with an rf drive frequency of Ω/2π = 20.8 MHz. Detection, cooling, and state preparation are performed on the ^{3}D_{1} → ^{3}P_{0} transition at 646 nm, with repump lasers at 350 and 622 nm to clear the ^{1}S_{0} and ^{3}D_{2} states, respectively (see Fig. 1a). The ^{1}S_{0} ↔ ^{3}D_{1} clock transition at 848 nm is a highly forbidden magnetic dipole (M1) transition with an estimated lifetime of 172 h^{23}; and the ^{1}S_{0} ↔ ^{3}D_{2} at 804 nm is a spinforbidden electric quadrupole (E2) transition with a measured lifetime of 17.3 s^{11}. Both 848 and 804 nm clock lasers are frequency offset locked to the same reference cavity which has finesse of 400,000 and 30,000 at the respective wavelengths.
The 10.6 μm radiation is produced by a 10 W CO_{2} laser. An acoustooptic modulator is used to control the optical power at the ion and as an optical switch, demonstrating better than 30 dB extinction. Two ZnSe vacuum viewports provide optical access to the ion. Displacement of the beam in the yzplane is achieved with mirrors on motorized translation stages, as shown schematically in Fig. 2a and detailed in Methods. The laser is linearly polarized along the zaxis. The optical power is monitored with a thermal power meter at the exit viewport and after a dichroic mirror. The measured transmissions of the ZnSe viewport and dichroic mirror at 10.6 μm are 0.990 (5) and 0.986 (5), respectively.
The light shift induced on the ^{3}D_{1}, 7, 0〉 ↔ ^{3}D_{1}, 6, 0〉 microwave transition has only a tensor contribution. This provides a useful diagnostic to determine the angle ϕ as the magnetic field is rotated: at ϕ = 90°, the light shift is at an extremum, and, at ϕ ≈ 54.7°, the light shift vanishes. At ϕ ≈ 90°, the light shift measured as a function of beam position determines the spatial profile of the laser beam. From the measured profile shown in Fig. 2b, a peak intensity relative to the incident optical power of I_{max}/P = 36.8 (8) mm^{−2} can be inferred (see Methods). The interrogation sequence for the microwave measurements is the same as in ref.^{22} with typical interrogation times of 10–50 ms depending on the desired Fourier limited resolution.
Polarizability measurements
To determine Δα_{0,J}(ν_{m}), the magnetic field is rotated to ϕ ≈ 54.7° where the tensor component of the lightshift vanishes. The 848 nm (804 nm) clock lasers are then stabilised to the average of the ^{1}S_{0}, 7, ±1〉 ↔ ^{3}D_{1}, 7, 0〉 (^{3}D_{2}, 9, 0〉) transitions (see Fig. 1b). The lightshift is measured by interrogating alternately with and without the CO_{2} laser and measuring the difference frequency between the two configurations. Typical interrogation times are 10–20 ms for the 848 nm transition and 1.5 ms for the 804 nm transition. Figure 3a shows the measured light shifts on the 848 nm clock transition (green points) as a function of CO_{2} laser power together with interleaved measurements of the microwave transition (yellow points) for tracking the suppression of the tensor shift. The observed deviations of the microwave transition frequency are consistent with fluctuations of either 0.2 μT in the transverse magnetic field or ~ 1 mrad in the CO_{2} laser polarization. The residual tensor shifts implied by the interleaved microwave measurements are removed from the optical measurements to generate the corrected data plotted in purple. A linear slope of −9.60 (13) HzW^{−1} is deduced by a χ^{2} fit to the corrected data. Figure 3b shows the light shifts on the 804 nm clock transition at the same magnetic field orientation and has a fitted slope 201.3 (2.2) Hz W^{−1}. Owing to the larger light shifts involved, corrections due to residual tensor shifts were unnecessary.
The tensor polarizabilities are separately assessed by measuring the light shifts at ϕ = 90°. Figure 3c shows the light shifts measured on the ^{3}D_{1}, 7, 0〉 ↔ ^{3}D_{1}, 6, 0〉 microwave transition with the fitted slope 530.4 (3.4) Hz W^{−1}. Figure 3d shows the light shifts on the ^{1}S_{0}, 7, 0〉 ↔ ^{3}D_{2}, 9, 0〉 optical transition with the fitted slope 431.0 (3.2) Hz W^{−1}, from which the ^{3}D_{2} tensor polarizability can be determined by subtracting the previously determined scalar component.
From the data presented in Fig. 3, we evaluate the dynamic polarizabilities, in atomic units, to be
The largest sources of systematic uncertainty are the accuracy of the thermal power meter, specified at 5%, and an additional 6% effect which we attribute to etalon interference (see Methods). In evaluating Δα_{0,1}(ν_{m}) we have included a 6.5% correction to account for the laser induced ac Zeeman shift (see Methods). We have not included consideration of the hyperfine mediated scalar polarizability for the ^{3}D_{1} levels^{7,24}. From estimates omitting the hyperfine corrections to the wavefunctions, it is unlikely that this would be comparable to the measurement uncertainty. Nevertheless, it would be of interest to have a more accurate assessment given the size of the measured value.
BBR shift analysis
Because the measured differential scalar polarizability on the ^{1}S_{0} ↔ ^{3}D_{1} transition is very small, the extrapolation to dc and the dynamic BBR shift contribution must be carefully considered. Over the BBR spectrum near room temperature, the scalar polarizability is well described by a quadratic approximation
For extrapolation to dc, we estimate the quadratic coefficient using the theoretical dipole transition matrix elements^{11} and experimental energies^{25}. Assuming 5% uncertainty in the theoretical matrix elements, we find Δα_{0,1}(0) = 0.018 (6) (a.u.). Evaluating the BBR shift by integrating the polarizability Eq. (4) over the BBR spectrum gives
where β = \(\frac{{40\pi ^2}}{{21}}\left( {\frac{{k_{\mathrm{B}}T_0}}{{h\nu _{\mathrm{m}}}}} \right)^2\) ≈ 0.918. Direct comparison of this expression to Eq. (1) relates our measured dynamic polarizability to the usual dynamic correction factor, η(T), up to quadratic terms. Because 10.6 μm is near to the center of the room temperature BBR spectrum, δν_{bbr} is relatively insensitive to the dc value Δα_{0,1}(0). At ~ 313 K, δν_{bbr} depends only on the measured value Δα_{0,1}(ν_{m}). The BBR shift evaluated at 300 K is −1.36(9) × 10^{−18}.
The insensitivity of the ^{1}S_{0} ↔ ^{3}D_{1} clock transition to temperature is illustrated in Fig. 4. Over the full range of 270–330 K the fractional uncertainty in the BBR shift remains below 1.0 × 10^{−18}. For more applicable laboratory conditions of 300 ± 5 K, indicated by the thin black lines, the fractional uncertainty is 2 × 10^{−19}.
At this level one might be concerned about the shift due to the magnetic field component of the BBR^{7}. In this case the largest contribution is due to coupling to the ^{3}D_{2} state. The approximation used in ref.^{7} for microwave transitions does not apply in this case and a numerical integration over the BBR spectrum must be used giving an estimated contribution of 3 × 10^{−20} at room temperature. The hyperfine mediated scalar polarisability^{7,24} will also contribute at the same order of magnitude with some cancelation due to hyperfine averaging^{9} expected.
For the ^{1}S_{0} ↔ ^{3}D_{2} transition, the dynamic BBR shift is small compared to the scalar shift and we can approximate Δα_{0,2}(0) ≈ Δα_{0,2}(ν_{m}). The corresponding fractional BBR shift is 2.70 (21) × 10^{−17} at 300 K.
For ion clocks, the value of Δα_{0} also has implications for micromotioninduced shifts. Micromotion driven by the rftrapping field gives rise to two correlated clock shifts: an ac Stark shift and a time dilation shift. The net micromotion shift, δν_{μ}, to lowest order, is given by^{17,26}:
where ν_{0} is the optical transition frequency in Hz, e is the electron charge, Ω is the trap drive frequency, m is the atomic mass, and \(\left\langle {E_\upmu ^2} \right\rangle\) is the mean squared electric field at frequency Ω. For clock transitions with Δα_{0} < 0, there exists a ‘magic’ drive frequency Ω_{0} = \(\frac{e}{{mc}}\sqrt {  \frac{{h\nu _0}}{{{\mathrm{\Delta }}\alpha _0}}}\) at which δν_{μ} vanishes. The suppression of micromotion shifts by operating at Ω_{0} has been applied in both ^{40}Ca^{+} and ^{88}Sr^{+} clocks^{17,27} and is advantageous for multiion clock schemes^{10,28}. An ideal clock candidate would have Δα_{0} < 0 which is small in magnitude to mitigate BBR shifts but sufficiently large to permit a practical value of Ω_{0}. The ^{1}S_{0} ↔ ^{3}D_{2} transition is in this ideal parameter regime with the lowest BBR shift among all such ionclock candidates and a magic drive frequency of Ω_{0}/2π ≈ 32.9 (1.3) MHz.
Discussion
With measurement of the differential scalar polarizabilities, all atomic properties of ^{176}Lu^{+} required to estimate clock systematics are known with sufficient accuracy to assess its future potential. The expected clock systematics for both transitions, after elimination of tensor shifts by hyperfine averaging^{9}, are summarized in Table 1. Achievable uncertainties in these systematic shifts are considered in reference to stateoftheart experimental techniques. The ^{1}S_{0} ↔ ^{3}D_{1} transition is uniquely insensitive to the BBR shift, leaving the residual micromotioninduced time dilation shift and acStark shifts from the clock laser as leading systematics. Sensitivity to motional shifts favours heavier ions where, for example, evaluation of excess micromotion to the 10^{−19} level has been demonstrated for ^{172}Yb^{+}^{28}. Using hyperRamsey spectroscopy^{29}, suppression of the probeinduced ac Stark shifts by four orders of magnitude has been demonstrated in Yb^{+}^{30}, for which the shift is two order of magnitude larger than in Lu^{+}. The ^{1}S_{0} ↔ ^{3}D_{2} transition has negligible probeinduced ac Stark shifts and net micromotion shifts can be heavily suppressed by operating near Ω_{0}. With improved accuracy in the polarizability measurement^{17} and a 1 K uncertainty in the temperature of the surroundings^{2}, the fractional BBR shift uncertainty could be reduced to the 10^{−19} level. For both Lu^{+} transitions, secondorder Doppler shifts due secular thermal motion are less than 10^{−19} for Dopplerlimited cooling^{10}.
The overall clock systematics compare favorably to other candidates, including ^{171}Yb^{+}^{2} and ^{27}Al^{+}^{3}, the two lowest uncertainty ion clocks reported at this time. The properties of the ^{171}Yb^{+} E3 clock transition offer no advantage over either Lu^{+} transition in any category of Table 1: the BBR shift is ~3 times larger than for Lu^{+} (^{3}D_{2}), micromotion considerations are comparable to Lu^{+} (^{3}D_{1}), and the probe acStark shift is two orders of magnitude larger than for Lu^{+} (^{3}D_{1}) for the same probe time. ^{27}Al^{+} has a BBR shift ~6 times larger^{3} than Lu^{+} (^{3}D_{1}), requires an auxiliary ion for sympathetic cooling and state detection, and motioninduced shifts present a greater technical challenge due to the relatively light mass^{31}. For experimental control comparable to that already demonstrated in the current generation of ionbased clock experiments, the systematics of ^{176}Lu^{+} suggest no significant hurdle for achieving evaluated uncertainties at the 10^{−18} level and beyond. Furthermore, its unique combination of atomic properties make ^{176}Lu^{+} a favoured candidate for multiion approaches^{10,28} to advance the stability of ionbased atomic clocks.
Methods
Optomechanical setup for beam displacement
The CO_{2} laser propagates in free space and is directed onto the ion by two mirrors and a lens to focus the laser on the ion. Displacement in the z(y)  direction is achieved by translating both (one) mirrors and the lens. Motorised translation stages were characterized by detecting the position of a visible laser overlapped with the CO_{2} laser using a CCD camera. The two axis of the motorized stages were found to be nonorthogonal by 4 mrad and this was subsequently corrected for in software. The rms positioning error measured by the camera was 0.7 (0.6) μm in the z (y) direction for a 2d profile scan comparable to the one shown in Fig. 2b.
Analysis of the laser profile
An approximate mode function is generated by cubic spline interpolation to the measurements shown in Fig. 2b. The peak intensity relative to the incident optical power is found by dividing the maximum light shift by the integral of this mode function over the interpolation region. The largest contributor to the uncertainty is the optical power instability of 1.5%. An elliptic TEM_{00} gaussian model fit to the data indicates <0.5% of the light shift distribution is truncated by the finite interpolation region.
Systematic uncertainties of the polarizabilities
We observe discrete jumps in the measured light shift, monitored over the course of the day, at intervals of approximately one hour within a 6% range. These discreet jumps are not correlated with the optical power measured at the thermal detector. We attribute this predominately to frequency mode hops of the CO_{2} laser which alters the effective transmission of the ZnSe viewport (dichroic mirror) between the thermal detector and ion by as much as 2% (2.7%) due to etalon effects. These frequency jumps occur on timescales longer than a typical data collection window. Because the CO_{2} laser frequency is not controlled, we conservatively add the maximum range of variation observed in the light shift (6%) as an independent error to the power meter accuracy. Radiation reflected from the ZnSe window back to the ion contributes negligible (<0.1%) additional uncertainty in the intensity at the ion.
Laser induced ac Zeeman shift
Due to the small magnitude of Δα_{0,1}(ν_{m}), shifts arising from the ac magnetic field of the CO_{2} laser should be considered. The most significant contribution arises from the magnetic dipole coupling between the ^{3}D_{1} and ^{3}D_{2} fine structure states, which are separated by ν_{0} ≈ 19.15 THz^{22}. The quadratic Zeeman shift can be evaluated following the same treatment as for the dipole polarizability^{21}. In the limit that the detuning is large relative to the hyperfine splitting, summation over all possible F′ results in a shift that can be broken down into scalar, vector, and tensor components. For linearly polarized light of frequency ν_{ m } the ac Zeeman shift for state ^{3}D_{1}, F, m_{ F }〉 is found to be
where \(\left {\left\langle {\,^3D_2\left\ {\bf{M}} \right\\,^3D_1} \right\rangle } \right\) is the M1 reduced matrix element in Bohr magnetons, \(\left\langle {B^2} \right\rangle\) is rms magnetic field, \(C_{F,m_F}\) is the same state dependant coefficient as in Eq. (2), and θ′ is the angle between the magnetic field and the quantization axis. Evaluated using the matrix element 2.055^{11}, we find the scalar shift on the ^{3}D_{1}, 7, 0〉 state is 0.627 Hz W^{−1}. This is subtracted from result shown in Fig. 3a to determine Δα_{0,1}(ν_{m}). In this experiment the tensor component of electric field was nulled and consequently the tensor component of the orthogonal magnetic field was not cancelled. However, this magnetic tensor shift is sufficiently small that it does not impact significantly on the accuracy to which the tensor component due to the electric field was nulled. Contributions from other magnetic couplings, such as to the ^{1}D_{2} state, are not statistically significant.
Data availability
All data presented and analyzed this study are available from the corresponding author upon reasonable request.
References
 1.
Nicholson, T. L. et al. Systematic evaluation of an atomic clock at 2×10^{−18} total uncertainty. Nat. Commun. 6, 6896 (2015).
 2.
Huntemann, N., Sanner, C., Lipphardt, B., Tamm, C. & Peik, E. Singleion atomic clock with 3×10^{−18} systematic uncertainty. Phys. Rev. Lett. 116, 063001 (2016).
 3.
Chou, C., Hume, D., Koelemeij, J., Wineland, D. J. & Rosenband, T. Frequency comparison of two highaccuracy Al^{+} optical clocks. Phys. Rev. Lett. 104, 070802 (2010).
 4.
Bauch, A. Caesium atomic clocks: function, performance and applications. Meas. Sci. Tech. 14, 1159 (2003).
 5.
Gill, P. Is the time right for a redefinition of the second by optical atomic clocks? J. Phys.: Conference Series, vol. 723, 012053 (IOP Publishing, 2016).
 6.
Riehle, F. Towards a redefinition of the second based on optical atomic clocks. Comptes Rendus Phys. 16, 506–515 (2015).
 7.
Itano, W. M., Lewis, L. L. & Wineland, D. J. Shift of ^{2} hyperfine splittings due to blackbody radiation. Phys. Rev. A 25, 1233–1235 (1982).
 8.
Porsev, S. G. & Derevianko, A. Multipolar theory of blackbody radiation shift of atomic energy levels and its implications for optical lattice clocks. Phys. Rev. A. 74, 020502 (2006).
 9.
Barrett, M. D. Developing a field independent frequency reference. New J. Phys. 17, 053024 (2015).
 10.
Arnold, K. et al. Prospects for atomic clocks based on large ion crystals. Phys. Rev. A 92, 032108 (2015).
 11.
Paez, E. et al. Atomic properties of Lu^{+}. Phys. Rev. A 93, 042112 (2016).
 12.
Kozlov, A., Dzuba, V. & Flambaum, V. Optical atomic clocks with suppressed blackbodyradiation shift. Phys. Rev. A 90, 042505 (2014).
 13.
Ludlow, A. D., Boyd, M. M., Ye, J., Peik, E. & Schmidt, P. O. Optical atomic clocks. Rev. Mod. Phys. 87, 637 (2015).
 14.
Middelmann, T., Falke, S., Lisdat, C. & Sterr, U. High accuracy correction of blackbody radiation shift in an optical lattice clock. Phys. Rev. Lett. 109, 263004 (2012).
 15.
Sherman, J. A. et al. Highaccuracy measurement of atomic polarizability in an optical lattice clock. Phys. Rev. Lett. 108, 153002 (2012).
 16.
Schneider, T., Peik, E. & Tamm, C. Subhertz optical frequency comparisons between two trapped ^{171}Yb^{+} ions. Phys. Rev. Lett. 94, 230801 (2005).
 17.
Dubé, P., Madej, A. A., Tibbo, M. & Bernard, J. E. Highaccuracy measurement of the differential scalar polarizability of a Sr^{+88} clock using the timedilation effect. Phys. Rev. Lett. 112, 173002 (2014).
 18.
Rosenband, T. et al. Blackbody radiation shift of the ^{27}Al^{+ 1}S_{0} → ^{3}P_{0} transition. In Frequency and Time Forum (EFTF), 2006 20th European, 289–292 (IEEE, 2006).
 19.
Tamm, C., Weyers, S., Lipphardt, B. & Peik, E. Strayfieldinduced quadrupole shift and absolute frequency of the 688–THz ^{171}Yb^{+} singleion optical frequency standard. Phys. Rev. A 80, 043403 (2009).
 20.
Arora, B., Safronova, M. & Clark, C. W. Magic wavelengths for the np − ns transitions in alkalimetal atoms. Phys. Rev. A 76, 052509 (2007).
 21.
Le Kien, F., Schneeweiss, P. & Rauschenbeutel, A. Dynamical polarizability of atoms in arbitrary light fields: general theory and application to cesium. Eur. Phys. J. D 67, 92 (2013).
 22.
Kaewuam, R., Roy, A., Tan, T. R., Arnold, K. J. & Barrett, M. D. Laser spectroscopy of ^{176}Lu^{+}. J. Mod. Opt. 65, 592–601 (2018).
 23.
Arnold, K. J. et al. Observation of the ^{1}S_{0} to ^{3} D _{1} clock transition in ^{175}Lu^{+}. Phys. Rev. A 94, 052512 (2016).
 24.
Dzuba, V. A., Flambaum, V. V., Beloy, K. & Derevianko, A. Hyperfinemediated static polarizabilities of monovalent atoms and ions. Phys. Rev. A 82, 062513 (2010).
 25.
Kramida, A., Ralchenko, Y., Reader, J. & the NIST ASD Team. NIST Atomic SpectraDatabase (version 5.5.3) (National Institute of Standards and Technology, Gaithersburg, MD, 2018).
 26.
Berkeland, D., Miller, J., Bergquist, J., Itano, W. & Wineland, D. Minimization of ion micromotion in a paul trap. J. Appl. Phys. 83, 5025–5033 (1998).
 27.
Cao, J. et al. A compact, transportable singleion optical clock with 7.8×10^{−17} systematic uncertainty. Appl. Phys. B 123, 112 (2017).
 28.
Keller, J., Burgermeister, T., Kalincev, D., Kiethe, J. & Mehlstäubler, T. Evaluation of trapinduced systematic frequency shifts for a multiion optical clock at the 10^{−19} level. J. Phys.: Conf. Series, vol. 723, 012027 (IOP Publishing, 2016).
 29.
Yudin, V. et al. Hyperramsey spectroscopy of optical clock transitions. Phys. Rev. A 82, 011804 (2010).
 30.
Huntemann, N. et al. Generalized ramsey excitation scheme with suppressed light shift. Phys. Rev. Lett. 109, 213002 (2012).
 31.
Chen, J. et al. Sympathetic ground state cooling and timedilation shifts in an ^{27}Al^{+} optical clock. Phys. Rev. Lett. 118, 053002 (2017).
Acknowledgements
We acknowledge J.S. Chen, S. Brewer and colleagues at the National Institute for Standards and Technology (NIST) for prompting us to evaluate the laser induced ac Zeeman shift. T. R. Tan acknowledges support from the Lee Kuan Yew postdoctoral fellowship. This research is supported by the National Research Foundation, Prime Ministers Office, Singapore and the Ministry of Education, Singapore under the Research Centres of Excellence programme. It is also supported by A*STAR SERC 2015 Public Sector Research Funding (PSF) Grant (SERC Project No: 1521200080).
Author information
Affiliations
Contributions
K.J.A., R.K., A.R., and T.R.T. performed the experiments. K.J.A. analysed the data and wrote the manuscript. M.D.B. conceived and supervised the project. All authors contributed to the construction of the experimental apparatus, discussed the results, and commented on the manuscript.
Corresponding authors
Correspondence to K. J. Arnold or M. D. Barrett.
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Arnold, K.J., Kaewuam, R., Roy, A. et al. Blackbody radiation shift assessment for a lutetium ion clock. Nat Commun 9, 1650 (2018). https://doi.org/10.1038/s4146701804079x
Received:
Accepted:
Published:
Further reading

Integrated multiple wavelength stabilization on a multichannel cavity for a transportable optical clock
Optics Express (2020)

Hyperfine Averaging by Dynamic Decoupling in a MultiIon Lutetium Clock
Physical Review Letters (2020)

Precision Measurements of the Ba+138 6sS21/2−5dD25/2 Clock Transition
Physical Review Letters (2020)

Magic wavelength of the Ba+138 6s S1/22–5d D5/22 clock transition
Physical Review A (2020)

Dynamic polarizability measurements with Lu+176
Physical Review A (2019)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.