Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Skin-inspired highly stretchable and conformable matrix networks for multifunctional sensing


Mechanosensation electronics (or Electronic skin, e-skin) consists of mechanically flexible and stretchable sensor networks that can detect and quantify various stimuli to mimic the human somatosensory system, with the sensations of touch, heat/cold, and pain in skin through various sensory receptors and neural pathways. Here we present a skin-inspired highly stretchable and conformable matrix network (SCMN) that successfully expands the e-skin sensing functionality including but not limited to temperature, in-plane strain, humidity, light, magnetic field, pressure, and proximity. The actualized specific expandable sensor units integrated on a structured polyimide network, potentially in three-dimensional (3D) integration scheme, can also fulfill simultaneous multi-stimulus sensing and achieve an adjustable sensing range and large-area expandability. We further construct a personalized intelligent prosthesis and demonstrate its use in real-time spatial pressure mapping and temperature estimation. Looking forward, this SCMN has broader applications in humanoid robotics, new prosthetics, human–machine interfaces, and health-monitoring technologies.


The human somatosensory system is a complex network that converts environmental stimuli into electrical impulses through various sensory receptors (mechanoreceptors, thermoreceptors, nociceptors, etc.) and transmits these signals via neural pathways, enabling the sensations of touch, heat/cold, and punching invasion. Consisting of mechanically flexible and stretchable sensor networks, mechanosensation electronics (electronic skin, e-skin)1,2,3,4,5,6 has been developed to mimic the human somatosensory system by detecting and quantifying various stimuli in the ambient environment and have attracted tremendous attention for their revolutionary applications in robotics7,8, prosthetics4,9,10, and health-monitoring technologies3,11,12. E-skin, which is capable of sensing different stimuli, is likely to boost emergence of the Internet of ‘actions’ (IoA), as we suppose, which would be a new era of health care, medical science, and robotics. The IoA would ascribe a world where billions of objects tightly integrated with sensors, processors, and actuators to sense stimuli and do actions interactively and adaptively; could naturally allow people to interact and communicate with the surroundings, including physical objects and external stimuli; and do some actions in response after computations13.

Mechanosensation electronics is supposed to be the core part of IoA2,11,14,15,16, and multi-functionalities are of essential importance in developing smart and interactive flexible/stretchable electronics2,15,16,17. Indeed, the ability to sense multiple stimuli is an ultimate goal for e-skin systems3,4,5. However, previous reports have mainly focused on single or dual sensory capabilities. Many emerging sensors, including pressure18,19,20,21, strain22,23,24,25,26,27,28, and temperature29,30, are underway to achieve excellent performance. Strain and temperature sensing were demonstrated by whisker arrays22 and thin film sensors31. Pressure sensing coupled with temperature (e.g., nanocomposites32, organic transistors33, thermoelectric34, or ferroelectric35 materials), strain (e.g., carbon nanotubes36, gold thin films26, or liquid conductors37 in silicone rubber, interlocked micro/nanostructures25,38,39, elastomer-based integrated tactile sensors10, energy-harvesting e-skin40), or proximity41,42 were also illustrated. Epidermal electronics11,43, piezoelectric sensors44, and micro-hairy sensors12 showed cutaneous and physiological monitoring. Si-nanoribbon strain, pressure, and temperature sensor arrays associated with humidity sensors and heaters were reported in a prosthetic skin9, but it did not show evidence of the sensory inputs recorded simultaneously. Surely, highly sensitive detections for different stimuli are not easy to implement due to decoupling interference of multiple signal34. Thus a simultaneous detection and high selectivity of multi-complex stimuli from the ambient environment remains a challenge, which puts high demands on a high-density sensor array4. Additionally, mechanoreceptor density varies widely for different areas of skin for a human, such as between fingertips (241 cm−2) and palms (58 cm−2)45. However, few reported e-skins achieved adjustable sensing range and area expansion46,47,48 in analogy of mechanoreceptors of the human skin.

Here we present a skin-inspired highly stretchable and conformable matrix network (SCMN) as a multi-sensory e-skin that is capable of detecting temperature, in-plane strain, relative humidity (RH), ultraviolet (UV) light, magnetic field, pressure, and proximity provides to realize simultaneous multi-stimulus sensing and exhibits an adjustable sensing range and large-area expandability, as well as potentially suitable for high-density three-dimensional (3D) integration scheme. More impressively, we likewise construct a personalized intelligent prosthetic hand for touch/temperature sensing that not only contour pressure distribution on fingers but also estimate temperatures of grasping objects simultaneously. This is a milestone using mechanosensation electronics toward IoA.


Skin-inspired SCMN for multifunctional sensing

Figure 1a schematically illustrates the human somatosensory system in the skin, which consists of neural networks that receive and transmit touch, heat/cold, and pain signals from the external environment. Moreover, various mechanoreceptors and thermoreceptors distributed in the epidermal and dermal layers enable the spatiotemporal recognition of the magnitude and location of touch and temperature stimuli49. As inspired by the human skin with this complex somatosensory system, we designed and fabricated a SCMN composed of 100 sensory nodes connected by meandering wires to achieve multifunctional sensing performance using stretchable and expandable structures (Fig. 1b), with corresponding tilted SEM images shown in Fig. 1c and its inset, respectively. The multilayered design layout and the corresponding fabrication process presented in Fig. 1d and Supplementary Fig. 1, respectively, show that six different types of sensor units are responsible for the different categories of sensing performance. Such design makes the device capable of detecting temperature, RH, UV light, magnetic field, in-plane strain, and pressure/proximity stimuli from the environment simultaneously. Furthermore, the SCMN shows a very good flexibility and stretchability due to the application of meandering interconnects, which are demonstrated in Fig. 1e.

Fig. 1
figure 1

Skin-inspired highly stretchable and conformable matrix networks. a Schematic illustration of SCMNs conforming to the surface of a human arm and an expanded network (expansion: 200%) conforming to the surface of a human abdomen (right); the tree branch-like connections of neurons (left bottom); the sensory receptors of the glabrous skin (left top). b Optical image of the fabricated polyimide network (10 × 10 array, scale bar: 5 mm). c Tilted SEM image of the polyimide network (scale bar: 500 μm); the inset is a higher resolution SEM image of a meandering interconnect (scale bar: 50 μm). d Schematic layout of an SCMN—an integrated sensor array with eight functions. (temp.: temperature). e Image of an SCMN attached to a sheet of paper, demonstrating ultrahigh flexibility and stretchability. The inset (upper) shows an SCMN conforming to a human finger, (middle) an SCMN attached to human skin with compression, and (bottom) an SCMN stretched by a human hand (scale bar: 1 cm)

SCMN stretchability and expandability

The meandering interconnects are critical for allowing the stable and uniform expansion of the network to several orders of magnitude larger than the original area and for the positioning of the nodes in predefined locations.

The stretching test is performed on a one-dimensional meandering interconnect, utilizing a customized stretch-testing platform (inset of Fig. 2a), and a detailed stretching procedure of a meandering wire can also be seen in Supplementary Movie 1. When the meandering wires are stretched from their original length (L/L0 = 1) to 800% expansion (L/L0 = 8), the extension of the wires presents a linear increase (shown in Fig. 2b), and the tensile force and resistance of the meandering wires show no obvious changes, which exhibits a superior stretchable and expandable capability. Upon mechanical deformation for over the designed ratio (L/L0 = 8), both the force and the resistance change exponentially with the strain, as shown in Fig. 2a. The meandering wires show a very good stability after 54,000 cycles at 300% expansion in durability tests (Fig. 2c). In addition, the relative resistance shows only a little increase (≤ 2.6%) with the reduction of bend radii; in particular, the meandering wires can be curved at a bend radius of 150 μm with good durability over 450 cycles (Fig. 2d).

Fig. 2
figure 2

Mechanical and electrical testing of the meandering interconnects. a Relative resistance and tensile force change with the extension of the meandering interconnects (50-μm-wide, 50-μm-thick polyimide wire coated with Ag thin films); the green section shows a perfectly stable performance region, and the inset depicts a schematic of the customized stretch-testing platform. b Optical images of a meandering wire stretched from an L/L0 of 1 to 8 (scale bar: 3 mm). c Durability testing at 300% expansion, with an inset showing the stretching at L/L0 = 1 and L/L0 = 3. d Relative resistance change vs. bend radius, with an inset showing bend durability at a bend radius of 150 μm. e Optical image of an expanding SCMN (scale bar: 2 cm), with an inset depicting an enlarged view of the red rectangle (scale bar: 5 mm). The network is made of 100 nodes (1.6 mm in diameter) connected by 50-μm-wide, 25-μm-thick polyimide wires coated with Au thin films. f Optical image of a twisted SCMN (scale bar: 2 cm)

By designing a matrix array of nodes connected to meandering wires, a network containing 100 nodes is successfully fabricated and placed on the customized stretch-testing platform (Supplementary Fig. 2a) to evaluate its stretchable and expandable performances. The polyimide (PI) network can be easily stretched and expanded along the desired directions (Fig. 2e and Supplementary Fig. 2b–i; Supplementary Movie 2), which achieves sensing area increase (Supplementary Fig. 2; Supplementary Movie 3), predefined sensory node location (Fig. 2f, Supplementary Figs. 2b and 3), and complex-shape object conform (Supplementary Fig. 3). These characteristics demonstrate the feasibility of SCMNs with adjustable sensing range and large-area expandability.

Temperature sensing

Resistive metals, platinum (Pt) and constantan alloy (45% Ni, 55% Cu), are most commonly used as resistance temperature detectors (RTDs) and strain gauges. Pt has a higher temperature but lower strain sensitivity when compared with constantan alloy, as shown in Supplementary Figs. 4a, b. A Pt thin film is deposited on the patterned nodes of the SCMN to act as a RTD, as shown in the inset of Fig. 3a. The temperature coefficient of resistance (TCR) is a key metric for evaluating the thermal response of temperature sensors and is defined as \({\mathrm{TCR}} = \frac{1}{{R_0}} \cdot \frac{{\Delta R}}{{\Delta T}}\), where R0 is the original resistance value of the Pt thin film at 0 °C and ΔR is the resistance change corresponding to the temperature change ΔT. Fig. 3a strikingly demonstrates that the relative resistance of the temperature sensor changes linearly as the temperature increases from 0 to 70 °C, and the obtained TCR of Pt is 2410 ppm/°C, which is comparable with the TCR value of commercial products (3850 ppm/°C). Moreover, the spatial temperature distribution can be easily recognized with temperature sensors diagonally on the SCMN (Supplementary Fig. 4c), and imaging temperatures close to 36.8 °C and 45.8 °C can be differentiated clearly, as shown in Fig. 3b. Additionally, resistance responses of the temperature sensor under different stimuli (e.g., pressure, UV light, magnetic field, and RH) are presented in Supplementary Fig. 5, which surely shows a favorable selectivity in temperature for the SCMN.

Fig. 3
figure 3

Multifunctional sensing performances. a, b Temperature sensing. a The relative resistance of the temperature sensor changes linearly with temperature; the inset depicts a Pt thin film temperature sensor fabricated on an SCMN. b Spatial temperature distribution recognition for temperatures close to 36.8 °C and 45.8 °C after placing a heat source above an SCMN. c, d In-plane strain sensing. c The relative resistance change increases with increasing applied strain; the inset shows a Constantan alloy thin film in-plane strain sensor mounted on an SCMN. (Error bars represent the fluctuation between normalized resistance and applied strain at each point.) d The temporal resistance changes for different curvatures of the strain sensor under cyclical bending (Strain: 0.7%, 1.3% and 1.5%). e, f Humidity sensing. e The change in capacitance is linear with increasing relative humidity (RH); the inset is an image of a humidity sensor on an SCMN. f Image of water droplets covering a partial area of a humidity senor array (left) and a corresponding map of the regional capacitance change (right). The red circles indicate where the droplets are placed. g, h Light sensing. g The photocurrent generated by UV light (355 nm) increases linearly with the light intensity; inset is an image of an optical sensor. h Repeatable UV response under different illumination intensities at a 5 V bias. i, j Magnetic sensing. i The GMR characteristics of a Co/Cu magnetic sensor; inset is an image of a magnetic sensor on an SCMN. j The recorded resistance changes when a magnet cyclically approaches (pink) and withdraws (white) from the sensor. Inset scale bars: 500 μm

In-plane strain sensing

Constantan alloy is used in our experiment as an in-plane strain gauge due to its high strain sensitivity and low TCR (Supplementary Figs. 4a, b). The gauge factor (GF) is defined as \({\mathrm{GF}} = \frac{{\Delta R/R_0}}{\varepsilon }\), where ΔR is the change in resistance caused by strain ε, and R0 is the resistance of the undeformed gauge. As shown in Fig. 3c, the relative change of resistance is linearly correlated with the applied strain, leading to a high GF of 18. The high GF may be mechanically induced using prebent samples with various radii of curvature50; the detailed strain calculation method is shown in Supplementary Fig. 6a and Supplementary Note 1. In addition, the temporal resistance changes for different curvatures of the strain sensor under cyclical bending (Strain: 0.7, 1.3, and 1.5%) reveal its favorable durability for sensing different strains (presented in Fig. 3d). Our device exhibits good in-plane strain discrimination to the other external stimuli, such as RH (Supplementary Fig. 6b), magnetic field (Supplementary Fig. 6c), pressure (Supplementary Fig. 6d), and UV light (Supplementary Fig. 6e), which have very small impacts on in-plane strain sensing, as shown in Supplementary Fig. 6. Upon attachment of the strain sensor to a human finger, the bending finger manners can be recorded by the SCMN, as shown in Supplementary Fig. 6f, indicating the potential for applications in health-monitoring systems, medical diagnostic instruments, and encrypted information transmissions.

Humidity sensing

Human skin contains no specific receptors for humidity sensing and is instead able to sense changes in humidity via mechanoreceptors and thermoreceptors51. In our device, a fabricated capacitor-based sensor, as shown in the inset of Fig. 3e, is used to sense ambient RH. The absorption of water molecules changes the permittivity of the PI and thus the capacitance of the humidity sensor, yielding a linear correlation between relative changes in capacitance and RH, which results in a slope of 0.07 (Fig. 3e). The fast response times of the humidity sensor for absorption (1.5 s) and desorption (50.6 s) are presented in Supplementary Fig. 7a. A good RH selectivity in multi-stimulus sensing of SCMN is presented as well, external stimuli, such as pressure loads (Supplementary Fig. 7b), temperature changes (Supplementary Fig. 7c), magnetic fields (Supplementary Fig. 7d), and in-plane strain (Supplementary Fig. 7e), have negligible effects on humidity sensing. Additionally, the capacitances of RH sensing do not show any noticeable changes although capacitance signals exhibit larger disturbances when UV light (3 mW cm−2) turns on (Supplementary Figs. 7f). Spatial humidity mapping clearly discriminates areas of the humidity sensor arrays that are only partially covered by water droplets (Fig. 3f), demonstrating the potential for use in detecting spatial differences in RH.

Light sensing

Sensing ambient light, including UV, visible and infrared (IR) light, is another important function of the artificial human somatosensory system. Humans can neither see nor differentiate the illumination intensity of UV or IR light, neither with eyes nor skins. Overexposure to UV or IR light can be harmful to the human body, hence it is necessary to achieve UV or IR light e-skin detecting. Additionally, the inclusion of optical sensors in e-skin would broaden the vision sensing range for humans. Here we take UV sensor based on ZnO as an example, while IR sensor, which can be achieved by depositing the corresponding sensitive material on the interdigital electrodes, is not demonstrated in this work yet. ZnO-based metal–semiconductor–metal sensors were integrated into the network, because ZnO is regarded as one of the most promising candidates for UV photodetection52. As shown in Supplementary Fig. 8a, a remarkable increase is observed in the current induced by 355 nm UV illumination (286.5 mW cm−2) at a 5 V bias, with a rapid response time at the rising edge of 41 ms (Supplementary Fig. 8b). Moreover, photocurrent induced by UV light is linear with respect to illumination intensity, resulting in a fast photo-responsivity R of 0.738 A/W, as shown in Fig. 3g. The good repeatability of UV sensors is investigated under various UV illumination intensities, as presented in Fig. 3h. External disturbances such as magnetic fields (Supplementary Fig. 8c), RH (Supplementary Fig. 8d), strain (Supplementary Fig. 8f), and pressure (Supplementary Fig. 8g) have negligible effects on UV light sensing. Normalized photocurrents exhibit a small growth due to the excited electron concentration of the conduction band in ZnO increasing as temperature (Supplementary Fig. 8e) but which would have a small impact on UV discrimination from other stimuli. Moreover, it is feasible to replace ZnO thin film with other materials, such as CdS for visible light and Ge/Si for IR light, implying the potential to expand light sensing by SCMNs to a wider spectral range.

Magnetic field sensing

Highly sensitive, giant magnetoresistive (GMR)-sensing elements composed of Co/Cu multilayers are deposited on the sensory nodes (inset of Fig. 3i), adding a “sixth sense”53 to the SCMN for the presence of static or dynamic magnetic field detection (magnetoreception). The GMR ratio \({\mathrm{GMR}}\left( {H_{\rm ext}} \right) = \left[ {R\left( {H_{\rm ext}} \right) - R_{\rm sat}} \right]/R_{\rm sat}\), is defined as the magnetic field dependence of changes in sensor resistance \(R\left( {H_{\rm ext}} \right)\) and normalized to the resistance value when the sample is magnetically saturated \(R_{\rm sat}\)53. We conduct a GMR characteristic measurement of as-fabricated [Co/Cu]50 multilayers at room temperature. A high GMR ratio of 50% is obtained (presented in Fig. 3i), which is a typical value for Co/Cu multilayers53,54. Then a permanent magnet is used to approach or withdraw from the sensor equipped with [Co/Cu]10 multilayers alternatively. The resistance changes with respect to the intensity of the magnetic field are derived by varying the distance between the sensor and the magnetic field, as shown in Fig. 3j and Supplementary Fig. 9a. Owing to the GMR effect, the resistance is observed to drop as the magnet is moving forward, while resistance recovers to the original value as the magnet is moving backward. Furthermore, when varying each other external stimulus (e.g., temperature, RH, UV light, pressure or in-plane strain, as shown in Supplementary Figs. 9b-f), changes in resistance all present little shifts by altering the same distance between the magnet and the sensor. And the resistance variations were recorded during the application of three different strains (0.85, 1.2, and 1.47%) independently and in conjunction with an approaching magnet (pink), as shown in Supplementary Fig. 9g, indicating that magnetic field sensing can be differentiated easily when applied strains. In short, this magnetoreceptive e-skin enables magnetic field proximity detection, navigation, and touchless control and essentially intensifies the sensing range of the e-skin.

Fig. 4
figure 4

Pressure and proximity sensing performances and area expansion. a Capacitance response to various pressures for two consecutive load tests. b Real-time small-pressure recording during the sequential application of six water droplets to the sensor; the corresponding pressure is 7.3 ± 1.2 Pa. c Pressure mapping of a number “6” stamped on the pressure sensor array with a pressure of 8 kPa. d Capacitance changes from a finger cyclically approaching the device (green, from a distance of approximately 1 cm), pressing it (pink) and moving away (white). e The relative capacitance change reduces with the decreasing distance of an approaching finger. The inset shows the capacitance difference as a finger repeatedly approaches the device. f Proximity detection of a hand and identification of its position. g Schematic illustration of an SCMN as an artificial electronic skin on a hand, showing sensing adjustability and expandability (scale bar: 1 cm). h Pressure mapping before and after the 300% expansion of an SCMN; the position of the pressure load is also identified after expansion

Pressure and proximity sensing

Dual-mode capacitor-based sensors can provide both pressure and proximity sensing capabilities for e-skin, extending the tactile sensing functionality in contact and non-contact modes24,41,42. The pressure and proximity sensor array is fabricated on the other side of the PI substrate, which is composed of an Ecoflex dielectric layer sandwiched between Ag thin film electrode layers and exhibits comparable performance in both pressure detection and object proximity sensing.

Pressures arouse an increase in capacitance of the sensor as a result of the reduced distance between the two Ag electrodes, regardless of RH, UV light, magnetic field, temperature, or in-plane strain (Supplementary Figs. 10a-e). Pressure sensing performance is evaluated based on pressure sensitivity, which is defined as \({\mathrm{\it S}} = \frac{{\Delta C/C_0}}{{\Delta P}}\), where ΔC is the capacitance change, C0 is the original capacitance of the device, and ΔP is the change in the applied pressure. The capacitance responses to various pressures for two consecutive loading tests is shown in Fig. 4a. Under pressures <16 kPa, the sensitivity of the fabricated pressure sensor is 22.4 MPa−1, which is larger than previously reported values24,36,55. Under pressures ranging from 16 to 360 kPa, the sensitivity of the pressure sensor is 1.25 MPa−1, which is comparable to the record values achieved by our previously reported pressure sensor (1.45 MPa−1 for pressures up to 100 kPa)24 and by Ag nanowire pressure sensors (1.62 MPa−1 for pressures up to 500 kPa)55. In addition, pressure as low as 7.3 ± 1.2 Pa is detected and recorded in real time by the sequential application of six water droplets to the sensor, as shown in Fig. 4b. The capacitance also returns to its original value after removal of the droplets, clearly indicating the ability to detect small pressures with superior stability. Furthermore, pressure distribution mapping of the 2D surface is also demonstrated by applying a stamp in shape of a “6” to the sensor array, as shown in Fig. 4c.

Figure 4d shows capacitance changes corresponding to a human finger approaching the device (green), gently pressing it (pink), and moving away (white). These results indicate that the pressure (contact) and proximity (non-contact) sensing modes coexist, and the detailed capacitance responses of the two modes are presented in Supplementary Fig. 10f. Capacitance changes are determined with a finger repeatedly approaching the device (green, from a distance of approximately 1 cm), pressing it (pink), and then moving away (white). Finger proximity leads to a decrease in capacitance, whereas physical contact induces an increase in capacitance by reducing the distance between the two electrodes. The capacitance changes with disturbances in the fringe electric field in either contact or non-contact mode, and Supplementary Fig. 10g illustrates the capacitive working mechanism.

Proximity signals from the SCMN change with respect to the distance of an approaching finger, and the capacitance drops sharply when the distance falls below 2 cm, as shown in Fig. 4e. Furthermore, tests comparing the capacitance-reduction signals of various materials, including copper, aluminum, PVC, glass, wood, ceramic, and a human hand41, indicate that the surface charge of the approaching material affects the electric field generated by the proximity sensors. In particular, an approaching hand elicits the largest change in capacitance41. The capacitance alternately decreases when a finger periodically approaches within 4 cm of the sensor and decreases further when the distance is reduced to 3 cm, as depicted in the inset of Fig. 4e. More importantly, the position of the approaching finger can be clearly identified, as illustrated by the position contour map in Fig. 4f. Therefore, this soft, capacitor-based sensor array enables the precise location/magnitude identification of pressures loads and approaching objects with high sensitivity, a rapid response, and high reversibility.

SCMN adjustable sensing range and area expansion

The spatial resolution of human tactile sensing varies across the body. For instance, the spatial resolution at fingertips is about seven times larger than that of palm56. As inspired by the variable spatial resolution of mechanoreceptors distributed in different parts of human skin, the SCMN, sensors with multiple sensory functions all integrated in a structured PI network as distributed layout (Supplementary Fig. 11a), does allow the density of the sensory nodes to be adjusted with the meandering structure stretching to represent areas of the skin with highly differing mechanoreceptor density. Besides, different functional sensors could be fabricated on the same sensory node in stack with insulation of PI dielectric thin films, regarded as stacked layout or 3D integration57,58 (schematically shown in Supplementary Fig. 11b), which will contribute to high density of mechanosensation electronics. Our fabricated SCMN, actually, is integrated by a combination of the distributed and stacked layouts (Supplementary Fig. 11c). Additionally, design rules of 3D stacked layouts for the multifunctional sensors are presented in Supplementary Table 1.

Figure 4g schematically illustrates the attachment of SCMN to an artificial hand as e-skin both with and without sensing area expansion, exhibiting superior area adjustability and expandability for multi-stimulus sensing (also depicted in Supplementary Fig. 3). As shown in Fig. 4h, spatial pressure mapping can be achieved before and after 300% expansion of the SCMN, indicating that SCMNs can be used to both identify the position of the pressure load and estimate the size of the loading object even with network stretching/expansion. Indeed, the SCMN could realize a 25-fold (or more) expansion of the sensing area, ranging from the original coverage (16 cm−2) to the expandable size (400 cm−2), shown in Supplementary Fig. 2. Furthermore, this property can be used to define the detection area not only for pressure but also for other external stimuli (e.g., temperature, in-plane strain, proximity, humidity, optical, magnetic field, etc.). These sensory nodes of the SCMN are adjustable and expandable to predefined locations for multifunctional sensing and, through network sensing area expansion, can be used to emulate the different densities of mechanoreceptors in the human skin.

Simultaneous multiple stimuli sensing

The fabricated SCMN, integration of temperature, in-plane strain, humidity, UV light, magnetic, pressure, and proximity sensors, can in real time record various signals induced from the external environment simultaneously, as well as differentiate each stimulus because of each flexible sensor having good selectivity and discrimination for external stimuli. The sensing ability and orthogonality between sensors in the SCMN are presented in the form of thumbnails in Supplementary Table 2, and the corresponding index is also shown in Supplementary Table 3.

Figure 5a shows real-time recording signals in temperature, pressure, and proximity simultaneously. The procedure involves artificial/human hand proximity, three consecutive pressure loads, human hand contact, and three-time breathing toward the SCMN. When an artificial wood hand or a human hand is brought to approach the SCMN with a distance of about 1 cm, the capacitances of the capacitor-based soft sensor are both triggered to decrease as the interferences of fringe electric field in non-contact mode. It is very noticeable that human hand approaching would lead to a much larger reduction in capacitance. However, the resistance of the temperature sensor does not show any obvious change during proximity sensing. Then placing three bottles (empty, filled with water, filled with hot water) on the SCMN in sequence. On the one hand, the capacitances of the pressure and proximity sensor exhibit corresponding increase rates with applying pressures (2.4, 4, and 3.2 kPa). On the other hand, the resistance of the temperature sensor begins to cause a sharp increase (up to a temperature of 33.2 °C correspondingly) when loading the third bottle that is filled with hot water and then recovers to the range of room temperature after removal of the bottle. With human hand contacts on the SCMN, both signals from proximity and temperature sensing change simultaneously. The capacitance falls to the lowest level, and the resistance arises to a corresponding skin temperature at 32.7 °C. Similarly, human breaths (exhale, containing moisture and heat) toward the SCMN for three times could bring the same change trends in capacitance and resistance as human hand contacts. Additionally, the detailed procedure is also shown in Supplementary Movie 4. Fig. 5b illustrates real-time multiple stimuli sensing as a permanent magnet put near or loaded on the SCMN. The magnetic field from the magnet causes a drop in resistance of the magnetic sensor when the magnet is moving close to the SCMN. Meanwhile, the fringe electric field of the soft sensor disturbed by the magnet also leads to a decrease in capacitance. With the proximity distances change between 1 cm and 2 cm alternatively, the resistance and the capacitance both show periodical fluctuations. Furthermore, a pressure of 5 kPa loaded on the SCMN by introducing the magnet induces an increase in capacitance for pressure sensing and makes it reach the minimum of resistance for magnetic sensing at the same time. The presence of magnet proximity/loading can be seen in Supplementary Movie 5. We can see the SCMN simultaneously monitoring three or more stimuli in Supplementary Fig. 12 as well. Notably, the specific sensor has a good selective detection for its sensitive stimuli, only with a little disturbances induced by other stimuli. More specifically, the coupled process of human finger contact/touch (Fig. 5a, and Supplementary Fig. 12a) and human exhale toward the SCMN (Fig. 5a, Supplementary Figs. 12b, c) can be recorded in real time and differentiated simultaneously.

Fig. 5
figure 5

Simultaneous multiple-stimuli sensing performances. a Real-time simultaneous sensing of temperature, pressure, and proximity stimuli. Signals in recording: Proximity—artificial/human hand approaches the SCMN with a distance of about 1 cm; Pressure—loading bottles on the SCMN with pressures of 2.4 kPa (empty), 4 kPa (filled with water), and 3.2 kPa (filled with hot water) consecutively; Contact—human hand on the SCMN; and Exhale—human breaths toward the SCMN for three times (Details are described in Supplementary Movie 4). b Real-time simultaneous sensing of magnetic field, pressure, and proximity stimuli. The detailed procedures of a permanent magnet put near or loaded on the SCMN: the magnet approaches the SCMN with a distance of about 1.5 cm; the proximity distances change between 1 cm and 2 cm alternatively; the magnet loaded on the SCMN corresponding to a pressure of 5 kPa (see Supplementary Movie 5)

Personalized intelligent prosthetic hand with pressure and temperature sensing

These capabilities of sensing pressure and temperature are essential features of the human skin3,4. As schematically shown in Fig. 6a, human hand can naturally differentiate temperatures when touching. Hence, we construct an intelligent prosthetic hand in personalized SCMN configuration, consisting of pressure and temperature sensor pixels on fingers, to facilitate simultaneous and sensitive pressure and temperature sensing. Pressure sensors integrated into the prosthetics could help disabled patients to regain the functionality of force sensing for grasp control and object manipulation. Furthermore, sensing temperature can provide information about the surroundings and avoid damaging temperatures. When the prosthetic hand is going to grasp a cup filled with water, temperature sensor would achieve cold/hot sensation for water and contribute to prevent injury from high temperatures. Notably, the prosthetic hand, adding the intelligent factor by means of multiple sensors integration, can not only contour pressure distribution on fingers but also estimate temperatures of grasping objects simultaneously.

Fig. 6
figure 6

The intelligent prosthetic hand with personalized SCMN configuration. a Schematic illustration of human hand picking up a cup with temperature detection at the same time. b Images show operations of the intelligent prosthetic hand to grasp (upper) and release (bottom). The procedures of grasping/releasing are also shown in Supplementary Movie 6. The intelligent prosthetic hand equipped with five pressure sensors (P1, P2, P3, P4, and P5) and one temperature sensor (T0) on fingers. c Pressure distribution contour on the fingers when the intelligent prosthetic hand is grasping a water cup and sensing temperature of 59.1 °C. dg The intelligent prosthetic hand grasps/releases cups filled with water with four different temperatures: 27 °C (d), 48 7 °C (e), 59.1 °C (f), and 71.2 °C (g). h Temperature estimation by the fitting equation when the intelligent prosthetic hand is grasping

The grasping and releasing operations of the intelligent prosthetic hand are visually described in Fig. 6b and Supplementary Movie 6. The intelligent prosthetic hand equipped with five pressure sensors (P1, P2, P3, P4, and P5) and one temperature sensor (T0) on fingers. Herein P1 is on the middle finger, P2, P3, and P4 are on the forefinger, and P5 and T0 are on the thumb, respectively. Their positions are also presented in Fig. 6c. By optimizing testing circuitry and shield setting, the interference from proximity signals is minimized, leading to a better sensing performance in contact mode. The intelligent prosthetic hand grasps/releases cups filled water with four different temperatures (water temperatures are measured with an infrared thermometer, respectively) are illustrated in Fig. 6d–g. When the intelligent prosthetic hand touches the cup, five pressure sensors (P1, P2, P3, P4, and P5) on fingers begin to increase the capacitance in pace with the increase of grip strength quickly, then the capacitance keeps small variations over a period of time at the peaks of grip strength. Meanwhile, temperature sensor (T0) also exhibits increment trend of resistance change at various degrees according to different water temperatures. The higher temperature causes a larger resistance change, which is just the same as mentioned above. Furthermore, capacitances of all five pressure sensors fast recover to the original values, and resistances of temperature sensor show recovery behavior as well, when the intelligent prosthetic hand coming to release. Impressively, pressure distribution on the fingers is illustrated in Fig. 6c, while the intelligent prosthetic hand grasping a cup with water temperature of 59.1 °C is illustrated in Fig. 6f. Compared with other pressure sensors on the fingers, the pressure sensor (P2) exhibits the largest capacitance change, which means that P2 bears the maximum grip pressure (about 200 kPa) in the grasp operation. Moreover, we are able to derive the linear relation between temperature and resistance according to the resistance values from 27, 48.7, and 71.2 °C. As shown in Fig. 6h, the resistance value from 59.1 °C is very close to the fitting one, representing a small variation of 2.6%. In effect, we can do temperature estimation through the experimental data and the fitting equation when the intelligent prosthetic hand is performing grasp/release operations. Briefly, the personalized intelligent prosthetic devices could allow amputees or individuals with nerve damage to regain considerable functionalities, such as touch and temperature sensing, to improve the rehabilitation and transform the lives and abilities of the disabled patients.


Skin-inspired highly stretchable and conformable matrix networks have been fabricated that integrate temperature, strain, humidity, light, magnetic, pressure, and proximity sensors as multifunctional detection matrix. The SCMN presented in this work successfully expands the sensing functionality of e-skin into seven categories, and it can simultaneously detect and differentiate three or more stimuli. Take the magnetic sensing and the pressure sensing as examples (Fig. 6b, Supplementary Movie 5, Supplementary Figs. 9 and 10), the SCMN works very well in different environment, like changing temperature, RH, UV intensity, or in-plane strain. Moreover, the sensing area of the SCMN can be adjusted and predefined by stretching and expanding the meandering interconnects, which acted as neural pathways. This skin-inspired SCMN, which features simultaneous multi-stimulus sensing, adjustable sensing range/large-area expandability, and potential high-density 3D integration, can sense the magnitude and location of multi-stimulus sensing in real time, impressively construct a personalized intelligent prosthesis for pressure/temperature sensing, and will likely attract considerable attention for its application to humanoid robotics, new prosthetics, human–machine interfaces, and health-monitoring technologies.


Fabrication of the highly stretchable and conformable PI networks

First, the Kapton HN film (DuPont) was cleaned by ultra-sonication with acetone, alcohol, and deionized water for 10 min; dried by N2 flow; and cured in an oven at 80 °C for 4 h. Second, a 3-inch silicon wafer was spin-coated with a 4-μm-thick photoresist layer, and then the Kapton film was bonded to the wafer using the hot-press method. Third, after being spin-coated with a 2-μm-thick negative photoresist layer (NR9-1500PY), the Kapton film was patterned by UV lithography (Suss MicroTech, MA 6). Fourth, Au (or Cr/Cu/Al/Ni) thin film (DC 100 W, 3 mTorr, 10 min) was deposited by sputter coating (Denton Vacuum, Discovery 635) and then lifted off to form a patterned Au mask. Fifth, the patterned Kapton film was etched (O2 plasma, 150 mTorr, 100 W) using a reactive ion etcher (South Bay Tech., RIE 2000). Finally, the etched Kapton film was released, and the metal mask was removed by wet or dry etching to obtain the highly stretchable and conformable PI networks.

Fabrication of expandable sensors and soft sensor array integrated on the SCMN

The fabrication process is illustrated in Supplementary Fig. 1. Step 1: A layer of poly (methyl methacrylate) (PMMA; 4,000 r.p.m. for 60 s, baked at 150 °C for 30 min) and a layer of PI (polyamide acid solution; 2,000 r.p.m. for 60 s and 4 h at 250 °C, four times to form a 30-µm film) were sequentially spin-coated onto a Si wafer. Step 2: Metal electrodes and dielectric layer preparation. Photolithography (NR9-1500PY, 2 µm), sputtered aluminum thin films, and lift-off photoresist were used to pattern the row and column meandering structures, and a PI dielectric layer (500 nm) was prepared between the electrodes. Step 3: Expandable sensor preparation consisted of photolithography (NR9-1500PY, 2 µm) to generate the sensor patterns, sputtering of the specific sensitive elements (Pt for temperature, Constantan for in-plane strain, Co/Cu multilayer for magnetic field, Al/PI for humidity, Al/ZnO for UV light, etc.), lift-off of the photoresists, and encapsulation of the patterned PI layer (3 µm). Additionally, the specific sensor patterns and elements for each stimulus are available in the literatures30,31,52,53,59,60,61. Step 4: Network preparation consisted of photolithography (NR9-1500PY, 2 µm) followed by sputtering of a SiO2 etching mask, lift-off of the photoresist, and reactive ion etching (RIE, O2 plasma, 150 mTorr, 200 W). Step 5: Network pickup and soft sensor array preparation. Immersion in hot acetone partially removed the PMMA layer, and the network was retrieved from the silicon wafer and attached to a piece of poly(vinyl alcohol) (PVA) or poly(dimethylsiloxane) (PDMS). Sputtered Ag thin films formed the bottom and top electrodes via a mask on the opposite side of the etched network structure, and Ecoflex silicone elastomers (Smooth-On 0010, mixing part A and part B with the ratio of 1:1 in weight, 300 r.p.m. for 50 s, cured at room temperature over one night, and cut into pad size) were placed on the sensory nodes between the two electrodes. Finally, some certain amounts of PDMS or PVA solutions were poured uniformly on the fabricated network and then baked at 60 °C for several hours. The SCMN with a layer of PDMS or PVA can be obtained.

Characterization of the integrated sensors

SEM images were obtained on a Hitachi SU8020. Applied force was measured using a force gauge (ATI, Nano 17). Sensor resistance and capacitance measurements were recorded on an Agilent (E4980A) Precision LCR meter with custom LabVIEW programs, and sensor currents were measured on a Keithley 4200 SC.

Data availability

All data supporting this study and its findings are available within the article and its Supplementary Information or from the corresponding author upon reasonable request.


  1. Takei, K. et al. Nanowire active-matrix circuitry for low-voltage macroscale artificial skin. Nat. Mater. 9, 821–826 (2010).

    ADS  CAS  Article  PubMed  Google Scholar 

  2. Wang, C. et al. User-interactive electronic skin for instantaneous pressure visualization. Nat. Mater. 12, 899–904 (2013).

    ADS  CAS  Article  PubMed  Google Scholar 

  3. Chortos, A. & Bao, Z. Skin-inspired electronic devices. Mater. Today 17, 321–331 (2014).

    CAS  Article  Google Scholar 

  4. Chortos, A., Liu, J. & Bao, Z. Pursuing prosthetic electronic skin. Nat. Mater. 15, 937–950 (2016).

    ADS  CAS  Article  PubMed  Google Scholar 

  5. Bao, Z. Skin-inspired organic electronic materials and devices. MRS Bull. 41, 897–904 (2016).

    Article  Google Scholar 

  6. Kim, S., Laschi, C. & Trimmer, B. Soft robotics: a bioinspired evolution in robotics. Trends Biotechnol. 31, 287–294 (2013).

    CAS  Article  PubMed  Google Scholar 

  7. Dahiya, R. S., Metta, G., Valle, M. & Sandini, G. Tactile sensing: from humans to humanoids. IEEE Trans. Robot. 26, 1–20 (2010).

    Article  Google Scholar 

  8. Rus, D. & Tolley, M. T. Design, fabrication and control of soft robots. Nature 521, 467–475 (2015).

    ADS  CAS  Article  PubMed  Google Scholar 

  9. Kim, J. et al. Stretchable silicon nanoribbon electronics for skin prosthesis. Nat. Commun. 5, 5747 (2014).

    CAS  Article  PubMed  Google Scholar 

  10. Gerratt, A. P., Michaud, H. O. & Lacour, S. P. Elastomeric electronic skin for prosthetic tactile sensation. Adv. Funct. Mater. 25, 2287–2295 (2015).

    CAS  Article  Google Scholar 

  11. Kim, D. H. et al. Epidermal electronics. Science 333, 838–843 (2011).

    ADS  CAS  Article  PubMed  Google Scholar 

  12. Pang, C. et al. Highly skin-conformal microhairy sensor for pulse signal amplification. Adv. Mater. 27, 634–640 (2015).

    CAS  Article  PubMed  Google Scholar 

  13. McEvoy, M. A. & Correll, N. Materials science. Materials that couple sensing, actuation, computation, and communication. Science 347, 1261689 (2015).

    CAS  Article  PubMed  Google Scholar 

  14. Tee, B. C. et al. A skin-inspired organic digital mechanoreceptor. Science 350, 313–316 (2015).

    ADS  CAS  Article  PubMed  Google Scholar 

  15. Gao, W. et al. Fully integrated wearable sensor arrays for multiplexed in situ perspiration analysis. Nature 529, 509–514 (2016).

    ADS  CAS  Article  PubMed  PubMed Central  Google Scholar 

  16. Chou, H. H. et al. A chameleon-inspired stretchable electronic skin with interactive colour changing controlled by tactile sensing. Nat. Commun. 6, 8011 (2015).

    CAS  Article  PubMed  PubMed Central  Google Scholar 

  17. Son, D. et al. Multifunctional wearable devices for diagnosis and therapy of movement disorders. Nat. Nanotechnol. 9, 397–404 (2014).

    ADS  CAS  Article  PubMed  Google Scholar 

  18. Mannsfeld, S. C. et al. Highly sensitive flexible pressure sensors with microstructured rubber dielectric layers. Nat. Mater. 9, 859–864 (2010).

    ADS  CAS  Article  PubMed  Google Scholar 

  19. Fan, F. R. et al. Transparent triboelectric nanogenerators and self-powered pressure sensors based on micropatterned plastic films. Nano Lett. 12, 3109–3114 (2012).

    ADS  CAS  Article  PubMed  Google Scholar 

  20. Lee, S. et al. A transparent bending-insensitive pressure sensor. Nat. Nanotechnol. 11, 472–478 (2016).

    ADS  CAS  Article  PubMed  Google Scholar 

  21. Wu, W., Wen, X. & Wang, Z. L. Taxel-addressable matrix of vertical-nanowire piezotronic transistors for active and adaptive tactile imaging. Science 340, 952–957 (2013).

    ADS  CAS  Article  PubMed  Google Scholar 

  22. Harada, S., Honda, W., Arie, T., Akita, S. & Takei, K. Fully printed, highly sensitive multifunctional artificial electronic whisker arrays integrated with strain and temperature sensors. ACS Nano 8, 3921–3927 (2014).

    CAS  Article  PubMed  Google Scholar 

  23. Frutiger, A. et al. Capacitive soft strain sensors via multicore-shell fiber printing. Adv. Mater. 27, 2440–2446 (2015).

    CAS  Article  PubMed  Google Scholar 

  24. Zhao, X., Hua, Q., Yu, R., Zhang, Y. & Pan, C. Flexible, stretchable and wearable multifunctional sensor array as artificial electronic skin for static and dynamic strain mapping. Adv. Electron. Mater. 1, 1500142 (2015).

    Article  Google Scholar 

  25. Pang, C. et al. A flexible and highly sensitive strain-gauge sensor using reversible interlocking of nanofibres. Nat. Mater. 11, 795–801 (2012).

    ADS  CAS  Article  PubMed  Google Scholar 

  26. Gong, S. et al. A wearable and highly sensitive pressure sensor with ultrathin gold nanowires. Nat. Commun. 5, 3132 (2014).

    PubMed  Google Scholar 

  27. Yamada, T. et al. A stretchable carbon nanotube strain sensor for human-motion detection. Nat. Nanotechnol. 6, 296–301 (2011).

    ADS  CAS  Article  PubMed  Google Scholar 

  28. Hua, Q. et al. Bioinspired electronic whisker arrays by pencil-drawn paper for adaptive tactile sensing. Adv. Electron. Mater. 2, 1600093 (2016).

    Article  Google Scholar 

  29. Yokota, T. et al. Ultraflexible, large-area, physiological temperature sensors for multipoint measurements. Proc. Natl. Acad. Sci. USA 112, 14533–14538 (2015).

    ADS  CAS  Article  PubMed  PubMed Central  Google Scholar 

  30. Webb, R. C. et al. Ultrathin conformal devices for precise and continuous thermal characterization of human skin. Nat. Mater. 12, 938–944 (2013).

    ADS  CAS  Article  PubMed  PubMed Central  Google Scholar 

  31. Lichtenwalner, D. J., Hydrick, A. E. & Kingon, A. I. Flexible thin film temperature and strain sensor array utilizing a novel sensing concept. Sens. Actuat. A Phys. 135, 593–597 (2007).

    CAS  Article  Google Scholar 

  32. Tien, N. T. et al. A flexible bimodal sensor array for simultaneous sensing of pressure and temperature. Adv. Mater. 26, 796–804 (2014).

    Article  PubMed  Google Scholar 

  33. Someya, T. et al. Conformable, flexible, large-area networks of pressure and thermal sensors with organic transistor active matrixes. Proc. Natl. Acad. Sci. USA 102, 12321–12325 (2005).

    ADS  CAS  Article  PubMed  PubMed Central  Google Scholar 

  34. Zhang, F., Zang, Y., Huang, D., Di, C. A. & Zhu, D. Flexible and self-powered temperature-pressure dual-parameter sensors using microstructure-frame-supported organic thermoelectric materials. Nat. Commun. 6, 8356 (2015).

    ADS  CAS  Article  PubMed  PubMed Central  Google Scholar 

  35. Park, J., Kim, M., Lee, Y., Lee, H. S. & Ko, H. Fingertip skin-inspired microstructured ferroelectric skins discriminate static/dynamic pressure and temperature stimuli. Sci. Adv. 1, e1500661 (2015).

    ADS  Article  PubMed  PubMed Central  Google Scholar 

  36. Lipomi, D. J. et al. Skin-like pressure and strain sensors based on transparent elastic films of carbon nanotubes. Nat. Nanotechnol. 6, 788–792 (2011).

    ADS  CAS  Article  PubMed  Google Scholar 

  37. Park, Y. L., Chen, B. R. & Wood, R. J. Design and fabrication of soft artificial skin using embedded microchannels and liquid conductors. IEEE Sens. J. 12, 2711–2718 (2012).

    CAS  Article  Google Scholar 

  38. Park, J. et al. Giant tunneling piezoresistance of composite elastomers with interlocked microdome arrays for ultrasensitive and multimodal electronic skins. ACS Nano 8, 4689–4697 (2014).

    CAS  Article  PubMed  Google Scholar 

  39. Park, J. et al. Tactile-direction-sensitive and stretchable electronic skins based on human-skin-inspired interlocked microstructures. ACS Nano 8, 12020–12029 (2014).

    CAS  Article  PubMed  Google Scholar 

  40. Park, S. et al. Stretchable energy-harvesting tactile electronic skin capable of differentiating multiple mechanical stimuli modes. Adv. Mater. 26, 7324–7332 (2014).

    CAS  Article  PubMed  Google Scholar 

  41. Hyung-Kew, L., Sun-Il, C. & Euisik, Y. Dual-mode capacitive proximity sensor for robot application: implementation of tactile and proximity sensing capability on a single polymer platform using shared electrodes. IEEE Sens. J. 9, 1748–1755 (2009).

    Article  Google Scholar 

  42. Zhang, B. et al. Dual functional transparent film for proximity and pressure sensing. Nano Res. 7, 1488–1496 (2014).

    Article  Google Scholar 

  43. Jeong, J. W. et al. Capacitive epidermal electronics for electrically safe, long-term electrophysiological measurements. Adv. Healthc. Mater. 3, 642–648 (2014).

    CAS  Article  PubMed  Google Scholar 

  44. Dagdeviren, C. et al. Conformable amplified lead zirconate titanate sensors with enhanced piezoelectric response for cutaneous pressure monitoring. Nat. Commun. 5, 4496 (2014).

    CAS  Article  PubMed  Google Scholar 

  45. Johansson, R. S. & Vallbo, A. B. Tactile sensibility in the human hand: relative and absolute densities of four types of mechanoreceptive units in glabrous skin. J. Physiol. 286, 283–300 (1979).

    CAS  Article  PubMed  PubMed Central  Google Scholar 

  46. Lanzara, G., Salowitz, N., Guo, Z. & Chang, F. K. A spider-web-like highly expandable sensor network for multifunctional materials. Adv. Mater. 22, 4643–4648 (2010).

    CAS  Article  PubMed  Google Scholar 

  47. Lanzara, G., Feng, J. & Chang, F. K. Design of micro-scale highly expandable networks of polymer-based substrates for macro-scale applications. Smart Mater. Struct. 19, 045013 (2010).

    ADS  Article  Google Scholar 

  48. Hyung-Kew, L., Sun-Il, C. & Euisik, Y. A flexible polymer tactile sensor: fabrication and modular expandability for large area deployment. J. Micro. 15, 1681–1686 (2006).

    Google Scholar 

  49. Purves, D. et al. (eds). in Neuroscience 2nd edn. (Sinauer Associates, Sunderland, MA, 2001). Available from:

  50. Kang, D. et al. Ultrasensitive mechanical crack-based sensor inspired by the spider sensory system. Nature 516, 222–226 (2014).

    ADS  CAS  Article  PubMed  Google Scholar 

  51. Ackerley, R., Olausson, H., Wessberg, J. & McGlone, F. Wetness perception across body sites. Neurosci. Lett. 522, 73–77 (2012).

    CAS  Article  PubMed  Google Scholar 

  52. Liu, K., Sakurai, M. & Aono, M. ZnO-based ultraviolet photodetectors. Sensors 10, 8604–8634 (2010).

    CAS  Article  PubMed  PubMed Central  Google Scholar 

  53. Melzer, M. et al. Imperceptible magnetoelectronics. Nat. Commun. 6, 6080 (2015).

    CAS  Article  PubMed  PubMed Central  Google Scholar 

  54. Melzer, M. et al. Stretchable magnetoelectronics. Nano. Lett. 11, 2522–2526 (2011).

    ADS  CAS  Article  PubMed  Google Scholar 

  55. Yao, S. & Zhu, Y. Wearable multifunctional sensors using printed stretchable conductors made of silver nanowires. Nanoscale 6, 2345–2352 (2014).

    ADS  CAS  Article  PubMed  Google Scholar 

  56. Craig, J. C. & Lyle, K. B. A comparison of tactile spatial sensitivity on the palm and fingerpad. Percept. Psychophys. 63, 337–347 (2001).

    CAS  Article  PubMed  Google Scholar 

  57. Shulaker, M. M. et al. Three-dimensional integration of nanotechnologies for computing and data storage on a single chip. Nature 547, 74–78 (2017).

    ADS  CAS  Article  PubMed  Google Scholar 

  58. Jiyoung, K. et al. A stacked memory device on logic 3D technology for ultra-high-density data storage. Nanotechnology 22, 254006 (2011).

    ADS  Article  Google Scholar 

  59. Oprea, A. et al. Temperature, humidity and gas sensors integrated on plastic foil for low power applications. Sens. Actuat. B Chem. 140, 227–232 (2009).

    CAS  Article  Google Scholar 

  60. Lee, H., Lee, S., Jung, S. & Lee, J. Nano-grass polyimide-based humidity sensors. Sens. Actuat. B Chem. 154, 2–8 (2011).

    CAS  Article  Google Scholar 

  61. Parkin, S. S., Bhadra, R. & Roche, K. P. Oscillatory magnetic exchange coupling through thin copper layers. Phys. Rev. Lett. 66, 2152–2155 (1991).

    ADS  CAS  Article  PubMed  Google Scholar 

Download references


The authors are thankful for support from the support of National Natural Science Foundation of China (No. 61405040, 51432005, 61505010 and 51502018), national key R & D project from Minister of Science and Technology of China (2016YFA0202703), and the “Thousand Talents” program of China for pioneering researchers and innovative teams.

Author information




Q.H. and C.P. conceived the idea, Q.H., C.P. and Z.L.W. discussed the data and prepared the manuscript. Q.H. and C.P. designed the structures of the multifunctional e-skin. Q.H. fabricated the SCMN and performed the data measurements. J.S., H.L., and R.B. provided assistance with the experiments. R.B. designed the prosthetic hand and analyzed the corresponding data. R.Y. and J.Z. helped with manuscript writing. All the authors discussed the results and commented on the manuscript.

Corresponding authors

Correspondence to Rongrong Bao, Caofeng Pan or Zhong Lin Wang.

Ethics declarations

Competing interests

The authors declare no competing financial interests.

Additional information

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Electronic supplementary material

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Hua, Q., Sun, J., Liu, H. et al. Skin-inspired highly stretchable and conformable matrix networks for multifunctional sensing. Nat Commun 9, 244 (2018).

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI:

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing