Abstract
Incorporating ferromagnetic dopants into threedimensional topological insulator thin films has recently led to the realisation of the quantum anomalous Hall effect. These materials are of great interest since they may support electrical currents that flow without resistance, even at zero magnetic field. To date, the quantum anomalous Hall effect has been investigated using lowfrequency transport measurements. However, transport results can be difficult to interpret due to the presence of parallel conductive paths, or because additional nonchiral edge channels may exist. Here we move beyond transport measurements by probing the microwave response of a magnetised disk of Cr(Bi,Sb)_{2}Te_{3}. We identify features associated with chiral edge plasmons, a signature that robust edge channels are intrinsic to this material system. Our results provide a measure of the velocity of edge excitations without contacting the sample, and pave the way for an onchip circuit element of practical importance: the zerofield microwave circulator.
Introduction
It is now understood that ferromagnetism, by lifting spin degeneracy and breaking time reversal symmetry at zero magnetic field, can transform a topological insulator (TI) into a new phase of matter that hosts chiral edge states^{1,2,3,4,5}. The signature of this phase is the quantum anomalous Hall effect (QAHE), in which the transverse conductance of a magnetised Hall bar remains quantised in units of the conductance quantum, even in the absence of an external magnetic field^{6, 7}. Experimentally, this has been demonstrated in (Bi,Sb)_{2}Te_{3} using chromium^{8,9,10} and vanadium^{11} dopants. Given that bulk insulators and ferromagnets are commonplace at room temperature, there is optimism that the QAHE may not be limited to the cryogenic regimes of today’s experiments. A roomtemperature QAHE, in which edge states propagate without dissipation, could impact some of the challenges facing currentgeneration high speed integrated circuits.
The presence of robust edge states in these material systems opens up the prospect that they support plasmonic edge excitations, resonant drummodes of the electron gas that are wellknown in the context of the quantum Hall effect^{12,13,14}. Beyond their fundamental interest, the velocity of edge plasmons excitations is typically reduced compared to the speed of light, making them ideal platforms for constructing onchip delay networks, highimpedance transmission lines, and nonreciprocal devices such as gyrators and circulators needed for quantum information processing in present low temperature setups^{15,16,17}. Recent theoretical work has also highlighted the potential of gapped Dirac materials to host chiral plasmons at optical frequencies, arising from the nonzero Bloch band Berry curvature^{18, 19}.
Here we investigate the zerofield plasmonic response of a magnetised, contactless disk of the ferromagnetic TI Cr(Bi,Sb)_{2}Te_{3}. The fabrication of both Hall bars and resonant disk structures enables us to make a onetoone comparison between the transport data and the microwave excitation spectrum of the material. By implementing a threeport circulator configuration, we show that the lowfrequency plasmon response exhibits nonreciprocal behaviour, which is consistent with chiral edge plasmons. The existence of such plasmonic modes in the disk and their correspondence with a minimum in the longitudinal resistance of the Hall bar provide further convincing evidence that this system supports a robust edge state. Finally, we examine the dependence of circulation on excitation power and temperature, suggesting that microwave measurements can serve as a sensitive probe of the conditions at the edge.
Results
Device details
Turning to the experimental setup shown in Fig. 1, the magnetic threedimensional (3D) TI used to make the circulator and corresponding Hall bar is seven quintuple layers of (Cr_{0.12}Bi_{0.26}Sb_{0.62})_{2}Te_{3}. The film is grown on a semiinsulating (111)B GaAs substrate by molecular beam epitaxy, then capped with alumina to protect the surface. To define the microwave circulator, we use photolithography to pattern a circular, 330 μm diameter mesa and etch away the remaining film via Ar ion milling. We next pattern capacitive contacts and a ground plane, depositing 120 nm Au by ebeam evaporation. The contacts are designed to be 20 μm away from the mesa edge.
Initial sample magnetisation
Starting at zero field, the transport data in Fig. 1c show the longitudinal and transverse resistances of the Hall bar, R _{ xx } and R _{ xy }, during the initial magnetisation sequence, sweeping the field from zero to B = −0.5 T at the cryostat base temperature of T = 20 mK (dark purple and green lines). As the field is applied for the first time we observe R _{ xx } drop from ~80 kΩ to ~500 Ω as R _{ xy } increases towards h/e ^{2} (h is Planck’s constant and e the electron charge). These resistance values are found to persist after waiting several hours at −0.5 T. The field is then swept back to zero, with transport data in this direction shown as lightlyshaded lines in Fig. 1c. Over this range, we observe that R _{ xy } does not vary by more than 1%, while R _{ xx } increases slowly to 2.3 kΩ at B = 0 T. An accurate and precise measurement of R _{ xy } requires accounting for possible geometric effects of the contacts and calibration using a known resistance standard, as was done in ref. ^{20}. In the absence of these corrections, the measured resistance plateau value of 25,750 Ω for this device is within the uncertainty expected for the quantum of resistance, 25,813 Ω^{8,9,10}.
We compare these transport data with the microwave response of an etched TI disk on the same material, configured as a circulator as shown in Fig. 1d–f. Similar designs comprising an rf excitation and detection port have been used to probe edge magnetoplasmons (EMPs) in the quantum Hall effect regime in GaAs semiconductors^{16, 21, 22} and in graphene^{23,24,25}. These EMP modes are charge density waves supported by edge channels at the boundary of the material. For traditional semiconductor samples, such as GaAs, the propagation velocity and therefore microwave frequency response of the EMP is set by the ratio of the electric and magnetic fields at the edge. In the case of ferromagnetic topological insulators, the existence of a robust edge is related to the electronic band structure, and can persist in the absence of an external magnetic field.
In our setup, a 3port design further allows the nonreciprocal character of the device to be probed by determining whether the signal traverses the TI disk via a lefthanded or righthanded path^{15, 16}. The experiment comprises Sparameter measurements in which the amount of microwave power transmitted from port 1 to port 2 (S _{21}), or port 3 to port 2 (S _{23}) is detected as a function of external magnetic field and magnetisation state \(\left( {M_z = M{\mathrm{/}}\left M \right = \pm 1} \right)\) of the TI disk (see Fig. 2a). The two symmetrical paths, port 1 to 2 and port 3 to 2, are designed to be equivalent in the absence of chiral transport.
We note that for any measurement, microwave power can be coupled directly and reciprocally between the ports via the geometric (parasitic) capacitance that shunts the disk (C _{p} in Fig. 1f). In our sample geometry C _{p} is estimated to be in the vicinity of a few hundred femtofarads. The combination of a direct capacitive path in parallel with the conductive edgechannels in the disk creates an interferometer in which signals travel at the speed of light in the capacitive arm, and at a velocity in the other arm that is determined by the plasmonic response^{16}. It is primarily the difference in velocities (and, to a lesser extent, path lengths) between the two paths of the interferometer that yields a phase offset between the two signals when they recombine at the receiving port. Further, the amplitude of the signals is set by the impedances of the two paths; if the edge plasmon resonator has a moderate Qfactor, these amplitudes can easily be made comparable by driving the circuit at a frequency slightly detuned from the resonant mode of the disk. Within this interference picture, the response of the circuit can be interpreted as a Fano resonance that depends on the length of path travelled by the edge plasmon, l or 2l depending on the excitation port and magnetisation direction (Fig. 2a). With port 2 always set to be the receiving port, transmitting power from port 1 or port 3 thus configures the edge length to be l or 2l. The difference between the two paths’ transmission, measured as S _{21} − S _{23}, determines the isolation or nonreciprocity of the circuit.
Microwave circulator response
We begin the presentation of the circulator data in a similar manner to the transport measurements, starting at zero magnetic field and recording S _{21} and S _{23} as the external field is stepped out to −0.5 T. To enable a direct comparison between transport and the microwave response of the disk during the oneoff magnetisation sequence, we acquire transport data as well as S _{21} and S _{23} at a fixed magnetic field before stepping the field (i.e., all data in Figs. 1c and 2 were obtained concurrently). All individual S _{21} and S _{23} data throughout the paper are normalised (denoted by Δ) by subtracting the initial frequency dependence of the signal in logarithmic units (dB) in the unmagnetised state, B = 0 and M _{ z } = 0, where the response is reciprocal. This calibration trace is taken at cryostat base temperature (T ~ 20 mK) and a port excitation power of −72 dBm. This normalisation alleviates frequencydependent artefacts, for instance transmission oscillations due to line impedance mismatch that do not evolve with magnetic field (Supplementary Fig. 1).
Forward transmission ΔS is shown in Fig. 2b, c as a function of frequency and magnetic field for the two paths S _{21} and S _{23}. As the sample begins to magnetise at the coercive field (~−0.16 T), we observe resonancelike dips and peaks in the frequency spectrum of the disk, evident as red and blue coloured horizontal bands appearing at the field strength where R _{ xy } (Fig. 1c) approaches the resistance plateau h/e ^{2}. This is the microwave signature of the QAHE. Compared with EMPs in 2dimensional electron systems^{16} where the frequency ω _{EMP} is proportional to 1/B, in the TI we observe a flat frequency band as a function of magnetic field, centred at the fundamental mode of the edge plasmon, near 400 MHz. This is consistent with dc transport measurements of the Hall resistance, which takes on a constant, quantised value after the sample is magnetised. Measuring the frequency at which these resonances occur in combination with the circumference of the TI disk gives a velocity at the fundamental mode of ~4 × 10^{5} m s^{−1}, similar to what is found in other structures comprising stacks of semiconductors^{16, 21, 22}.
The microwave response shows that the parameters S _{21} and S _{23} deviate from each other as the disk becomes magnetised. This is a result of the nonreciprocity of the system, evident in Fig. 2d, where we have subtracted the bare Sparameters (S _{21} − S _{23}) from each other to show the difference between the two configurations of the circulator. Again, we interpret these measurements of S _{21} and S _{23} as characterising paths around the edge of the disk in the same (chiral) direction with arclength l and 2l (Fig. 2a). Considering the measurement in Fig. 2d, it is apparent that microwave power can both circulate near the fundamental edge plasmon frequency (blue frequency band) and counter circulate in an opposite direction near the first harmonic (red frequency band). This behaviour is also observed for GaAs devices in the quantum Hall regime^{16} and is understood to arise from a Fanolike interference between the slowvelocity resonantly circulating edge mode and the parallel capacitive path^{26}. We remark that the observation of circulation and countercirculation is a further signature of the plasmonic response of the chiral edge state.
Sweeping the magnetic field
The quantum anomolous Hall effect is unique in that it supports a chiral edge state at zero applied field^{20}. To examine the zerofield response of the magnetised TI system, we continue to take transport measurements on the Hall bar concurrent with Sparameter data on the circulator, as the system is swept from positive to negative field through zero, as shown in Fig. 3a, b. The transport data in Fig. 3c show the familiar signature of the QAHE with R _{ xx } peaking and R _{ xy } switching sign at the coercive field indicated by the blue dashed line (~−0.16 T). At B = 0, the system remains magnetised with R _{ xy } reaching a maximum value of 25.75 kΩ.
In comparison to the transport measurements, the microwave response of the TI reveals new information. The response of the disk for each of the signal configurations, characterised by ΔS _{21} in Fig. 3a and ΔS _{23} in Fig. 3b, is strongly asymmetric about the coercive field. Symmetry is restored, however, if in addition to the sign of the magnetisation, the ports are also interchanged, so that the red band in ΔS _{21} on the left of the coercive field mirrors the red band in ΔS _{23} on the right, and vice versa for blue features. This strong nonreciprocity is most evident in the differential form of the data S _{21} − S _{23}, as shown in Fig. 3d. At zero field, the circulator continues to exhibit nonreciprocity ~10 dB (Fig. 3e). Intriguingly, the device is maximally nonreciprocal at a field approaching the coercive field, producing a hotspot feature in the Sparameter response (mauve dashedline Fig. 3d). As described below, we suggest these features are linked to enhanced dissipation.
Power and temperature dependence
Finally, we investigate the temperature and microwave power dependence of the edge plasmon spectra in an effort to better understand the details of the zerofield edge state. At B = 0 and with the TI magnetised (M _{ z } = −1), ΔS _{21} and ΔS _{23} are measured as a function of applied microwave power P, as shown in Fig. 4a, b. In addition to the usual nonreciprocity at constant power, we observe an evolution in the nonreciprocal features with increasing P that is dependent on the length of the edge segment. While the response of ΔS _{21} (characterised by arclength l) begins to fade out at high powers, the amplitude of ΔS _{23} (2l) changes sign near the fundamental frequency and exhibits a pronounced minimum or hotspot near P = −60 dBm. Interchanging the ports and repeating the measurement at M _{ z } = +1 and B = 0 produces similar features in accordance with a reversal of chirality (Supplementary Fig. 2). Mirroring the dependence with power, increasing the cryostat temperature also produces a change of sign relative to the premagnetised state for the longer edge path (2l): raising T as in Fig. 4c, d leads to ΔS _{21} becoming gradually washed out, while ΔS _{23} produces a hotspot around T = 85 mK. This effect is further illustrated in Fig. 4, where 1D cuts at constant power (e) or temperature (f) are shown for ΔS _{23}.
Discussion
Socalled hotspots—characterised by a strong decrease in the microwave power transmitted between ports—occur at particular magnetic fields, powers, or temperatures. Appealing to the phenomenology of the interferometer pictured in Fig. 1f, we note that the direction of power transmission between ports, either circulation or countercirculation, is set by the relative phase and amplitude of the signals in the edgestate arm compared to the direct capacitive arm of the interferometer. In general, this picture accounts for the constructive interference of signals for the shorter edge path (l) and destructive interference for the longer (2l), when driving near resonance of the edge plasmon fundamental mode.
Extending this picture to include dissipation, we suggest that losses in either arm of the interferometer can adjust the relative amplitudes. As noted above, the relative phase of the two paths is naturally tuned by π upon crossing the edge plasmon resonance. At a frequency where the relative phase is π we might expect a sign change in the relevant Sparameter response. In this way, the hotspots can be understood as regions where almost perfect cancellation between the two arms occurs. The appearance of dissipation in either path with increasing temperature, microwave power, or near the coercive field is perhaps not unexpected. Accounting for the microscopic mechanisms underlying such dissipation remains an open challenge^{20, 27,28,29,30,31,32}, given that all measurements are well below both the Curie temperature of these ferromagnetic TIs (of order 10 to 20 K) and the energy scale of the exchange gap as measured by ARPES (of order 10 meV). We note that the hotspot onset temperature of 85 mK is consistent with experimentally determined activation gaps on similar growths^{20}, although we cannot rule out the possibility of parallel or counterpropagating paths.
To conclude, we have probed the plasmonic edge spectrum of a magnetic topological insulator, comparing its microwave response to the transport data. The measurement setup can be understood as an interferometer with the disk of TI in one arm of the interferometer and a parasitic capacitance in the other. Within this picture, the response of the system exhibits resonances that can be explained by accounting for the slow velocity of edge plasmons as they traverse an arclength of the TI disk’s edge rather than the bulk. In addition to the device examined, we have studied a second circulator, fabricated from a separatelygrown wafer, and found it to exhibit strikingly similar behaviour in all aspects (see Supplementary Fig. 3). We suggest that this similarity between devices is related to the robust properties of the edge state, set by the nontrivial topology of the material system rather than, for instance, the specific configuration of microscopic disorder. Taken together, our microwave measurements provide strong evidence that this material system indeed supports robust, chiral edge states at zero magnetic field, opening the prospect of compact microwave components based on magnetic topological insulators.
Methods
Fabrication details
The film used to make the circulator and corresponding Hall bar is seven quintuple layers of (Cr_{0.12}Bi_{0.26}Sb_{0.62})_{2}Te_{3}. We use photolithography to pattern a circular mesa with a diameter of 330 μm. We bake the Megaposit SPR 3612 photoresist at 80 °C (to avoid possible damage to the film from overheating), and develop with MF CD30 after exposure. To define the mesa, we etch the surrounding film via Ar ion milling. After patterning the contacts and ground plane with the same photolithographic procedure, we deposit a 5 nm Ti sticking layer followed by 120 nm Au using ebeam evaporation. The capacitive contacts are designed to be 20 μm from the edge of the circular mesa. For the primary device discussed in this work, the relative misalignment of the mesa and contacts is approximately 5 μm.
Data availability
The data that support the findings of this study are available from the corresponding authors upon reasonable request.
References
Qi, X.L., Hughes, T. L. & Zhang, S.C. Topological field theory of timereversal invariant insulators. Phys. Rev. B 78, 195424 (2008).
Liu, C.X., Qi, X.L., Dai, X., Fang, Z. & Zhang, S.C. Quantum anomalous Hall effect in Hg_{1−y }Mn_{ y } Te quantum wells. Phys. Rev. Lett. 101, 146802 (2008).
Yu, R. et al. Quantized anomalous Hall effect in magnetic topological insulators. Science 329, 61–64 (2010).
Qi, X.L. & Zhang, S.C. Topological insulators and superconductors. Rev. Mod. Phys. 83, 1057 (2011).
Nomura, K. & Nagaosa, N. Surfacequantized anomalous Hall current and the magnetoelectric effect in magnetically disordered topological insulators. Phys. Rev. Lett. 106, 166802 (2011).
Haldane, F. D. M. Model for a quantum Hall effect without Landau levels: condensedmatter realization of the “parity anomaly”. Phys. Rev. Lett. 61, 2015 (1988).
Hasan, M. Z. & Kane, C. L. Colloquium: topological insulators. Rev. Mod. Phys. 82, 3045 (2010).
Chang, C.Z. et al. Experimental observation of the quantum anomalous Hall effect in a magnetic topological insulator. Science 340, 167–170 (2013).
Kou, X. et al. Scaleinvariant quantum anomalous Hall effect in magnetic topological insulators beyond the twodimensional limit. Phys. Rev. Lett. 113, 137201 (2014).
Checkelsky, J. et al. Trajectory of the anomalous Hall effect towards the quantized state in a ferromagnetic topological insulator. Nat. Phys. 10, 731–736 (2014).
Chang, C.Z. et al. Highprecision realization of robust quantum anomalous Hall state in a hard ferromagnetic topological insulator. Nat. Mater. 14, 473–477 (2015).
Volkov, V. & Mikhailov, S. Edge magnetoplasmonslowfrequency weakly damped excitations in homogeneous twodimensional electron systems. Zh. Eksp. Teor. Fiz. 94, 217–241 (1988).
Ashoori, R., Stormer, H., Pfeiffer, L., Baldwin, K. & West, K. Edge magnetoplasmons in the time domain. Phys. Rev. B 45, 3894 (1992).
Talyanskii, V. et al. Spectroscopy of a twodimensional electron gas in the quantumHalleffect regime by use of lowfrequency edge magnetoplasmons. Phys. Rev. B 46, 12427 (1992).
Viola, G. & DiVincenzo, D. P. Hall effect gyrators and circulators. Phys. Rev. X 4, 021019 (2014).
Mahoney, A. C. et al. Onchip microwave quantum Hall circulator. Phys. Rev. X 7, 011007 (2017).
Bosco, S., Haupt, F. & DiVincenzo, D. P. Selfimpedancematched Halleffect gyrators and circulators. Phys. Rev. App. 7, 024030 (2017).
Song, J. C. W. & Rudner, M. S. Chiral plasmons without magnetic field. Proc. Natl. Acad. Sci. USA 113, 4658–4663 (2016).
Kumar, A. et al. Chiral plasmon in gapped Dirac systems. Phys. Rev. B 93, 041413 (2016).
Bestwick, A. et al. Precise quantization of the anomalous Hall effect near zero magnetic field. Phys. Rev. Lett. 114, 187201 (2015).
Kamata, H., Ota, T., Muraki, K. & Fujisawa, T. Voltagecontrolled group velocity of edge magnetoplasmon in the quantum Hall regime. Phys. Rev. B 81, 085329 (2010).
Kumada, N., Kamata, H. & Fujisawa, T. Edge magnetoplasmon transport in gated and ungated quantum Hall systems. Phys. Rev. B 84, 045314 (2011).
Petković, I. et al. Carrier drift velocity and edge magnetoplasmons in graphene. Phys. Rev. Lett. 110, 016801 (2013).
Kumada, N. et al. Plasmon transport in graphene investigated by timeresolved electrical measurements. Nat. Commun. 4, 1363 (2013).
Kumada, N. et al. Resonant edge magnetoplasmons and their decay in graphene. Phys. Rev. Lett. 113, 266601 (2014).
Placke, B., Bosco, S. & DiVincenzo, D. P. A model study of presentday Halleffect circulators. EPJ Quant. Technol. 4, 5 (2017).
Chang, C.Z. et al. Zerofield dissipationless chiral edge transport and the nature of dissipation in the quantum anomalous Hall state. Phys. Rev. Lett. 115, 057206 (2015).
Wang, J., Lian, B., Zhang, H. & Zhang, S.C. Anomalous edge transport in the quantum anomalous Hall state. Phys. Rev. Lett. 111, 086803 (2013).
Wang, J., Lian, B. & Zhang, S.C. Universal scaling of the quantum anomalous Hall plateau transition. Phys. Rev. B 89, 085106 (2014).
Kou, X. et al. Metaltoinsulator switching in quantum anomalous Hall states. Nat. Commun. 6, 8474 (2015).
Feng, Y. et al. Observation of the zero Hall plateau in a quantum anomalous Hall insulator. Phys. Rev. Lett. 115, 126801 (2015).
Li, W. et al. Origin of the low critical observing temperature of the quantum anomalous Hall effect in Vdoped (Bi, Sb)_{2}Te_{3} film. Sci. Rep. 6, 32732 (2016).
Acknowledgements
We thank Andrew Doherty and David DiVincenzo for useful conversations. Device fabrication and preliminary characterisation was supported by the Department of Energy, Office of Science, Basic Energy Sciences, Materials Sciences and Engineering Division, under Contract DEAC0276SF00515. Microwave and transport measurements presented in the main text were supported by Microsoft Research, the Army Research Office grant W911NF1410097, the Australian Research Council Centre of Excellence Scheme (Grant No. EQuS CE110001013). Materials growth was supported by the DARPA MESO program under Contracts No. N660011214034 and No. N660011114105. Infrastructure and cryostat support were funded in part by the Gordon and Betty Moore Foundation through Grant GBMF3429. E.J.F. acknowledges support from a DOE Office of Science Graduate Fellowship. L.P. was supported by a Stanford Graduate Fellowship.
Author information
Authors and Affiliations
Contributions
A.C.M., J.I.C, L.P. and S.J.P.: Carried out the experiments. E.J.F.: Fabricated the sample. The material was grown by X.K., L.P. and K.L.W. The manuscript was written by D.J.R, A.C.M. and D.G.G. with input from all coauthors.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Mahoney, A.C., Colless, J.I., Peeters, L. et al. Zerofield edge plasmons in a magnetic topological insulator. Nat Commun 8, 1836 (2017). https://doi.org/10.1038/s41467017019845
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467017019845
This article is cited by

Advance in twodimensional twisted moiré materials: Fabrication, properties, and applications
Nano Research (2023)

Topological current divider in a Chern insulator junction
Nature Communications (2022)

Topological spintronics and magnetoelectronics
Nature Materials (2022)

Magnetic topological insulators
Nature Reviews Physics (2019)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.