Thermal energy storage offers enormous potential for a wide range of energy technologies. Phase-change materials offer state-of-the-art thermal storage due to high latent heat. However, spontaneous heat loss from thermally charged phase-change materials to cooler surroundings occurs due to the absence of a significant energy barrier for the liquid–solid transition. This prevents control over the thermal storage, and developing effective methods to address this problem has remained an elusive goal. Herein, we report a combination of photo-switching dopants and organic phase-change materials as a way to introduce an activation energy barrier for phase-change materials solidification and to conserve thermal energy in the materials, allowing them to be triggered optically to release their stored latent heat. This approach enables the retention of thermal energy (about 200 J g−1) in the materials for at least 10 h at temperatures lower than the original crystallization point, unlocking opportunities for portable thermal energy storage systems.
Phase-change materials (PCMs), such as salt hydrates1, metal alloys2, or organics3, store thermal energy in the form of latent heat, above their phase-transition temperature, which is released via reverse-phase transformation4. Long-term storage of latent heat without loss to the environment remains a challenge5 due to the sensitivity of phase-transition to temperature, which fundamentally prevents the deployment of thermally charged PCMs away from heat sources. One way to prevent this spontaneous heat loss is to install an energy barrier for the reverse-phase change from a high-energy phase to a low-energy phase. In some materials, intrinsic energy barriers exist, and the controlled heat release is feasible by applying external mechanical energy to overcome the barriers. For example, flexing metal clips in pockets of supersaturated salt hydrate and the application of external pressure on a ceramic material have been shown to trigger heat release from certain inorganic PCMs, but they suffer from inherent limitations. In the case of salt hydrates, the instability of the salt solution, decreasing the storage density upon cycling, and corrosiveness are the major issues that have not been resolved6. Ceramics, on the other hand, require a high-cost synthesis process (sintering metal oxides at T over 1000 °C), and possess low- energy densities (50–60 J g−1) compared to conventional inorganic or organic PCMs (100–600 J g−1)7. Moreover, mechanical triggering for both cases is limited by the high cost for large-scale applications.
Organic phase-change materials, such as low-cost paraffin waxes8, fatty acids9,10, polyethylene glycols11, and sugar alcohols12, generally exhibit large latent heat and solid–liquid phase transitions, covering a wide range of melting and crystallization points13. Since the phase changes are governed by intermolecular interactions, including van der Waals, dipolar, and hydrogen bonding, the phase- transition temperatures and thermal energy densities can be controlled by tuning these key interactions between constituents.
Organic photoswitches that undergo reversible structural changes upon light irradiation have been integrated into various materials for applications, including light-driven actuation, drug delivery, sensing, optical memory, and so on14,15. Among photochromic molecules, such as spiropyran16,17, azobenzene18,19,20,21, fulvalene diruthenium22, and dithienylethene23,24, azobenzene has been widely explored due to its well-known shape (molecular length of 9 Å for trans, 5.5 Å for cis; planar geometry in trans, the benzene ring tilted at 56° from the other ring in cis)25 and polarity changes (dipole moment of 0−1.2 D for trans, 3.1−4.4 D for cis)26 upon photoisomerization. The planar-to-twisted conformational change of azobenzene upon UV irradiation and the reverse isomerization triggered by visible-light illumination can be utilized to alter the physical properties of surrounding molecules through the change in intermolecular interactions.
Herein, we introduce azobenzene dopants into conventional organic PCMs as a way to change the intermolecular dynamics. These dopants, possessing activation energy barriers for switching between photoisomers, provide stability to the phase storing thermal energy and triggerabilty for energy release, thus allowing controllable, high-density energy storage in scalable organic composites. Specifically, the azobenzene dopants that change conformation upon illumination can be locked in the liquid phase of PCMs by lowering their crystallization temperature (T c), retaining the thermal energy storage at cooler temperatures.
Thermal energy storage and release in PCM composites
We prepared a composite of tridecanoic acid, as an example of n-fatty acids with high heat of fusion (177 J g−1), and an azobenzene dopant that is functionalized with a tridecanoic ester group to render high miscibility with the PCM molecules. Long aliphatic compounds such as n-fatty acids or n-paraffin waxes form lamellar structures through hydrocarbon side packing (i.e., van der Waals forces), and the CH3 end-group interaction between the lamellae can affect the molecular arrangement as well, leading to polymorphism27. In the case of n-fatty acids with –COOH groups, the polar interaction and H-bonding between the acid groups can also impact the lamellar formation28. The azobenzene dopants possess strong π–π interactions29 among adjacent aromatic cores and van der Waals interactions between alkyl chains. Ester linkers are also expected to contribute to intermolecular interactions.
The first step in the thermal storage cycle is the absorption of external thermal energy by the solid composite that is crystalline as prepared (Fig. 1a, i). When heated above the melting point (T m) of the PCM (42 °C), the composite becomes a mixture of molten PCM and crystalline aggregates of the azobenzene dopant, which has a higher melting point of 73 °C (Fig. 1a, ii). Then UV illumination of the slurry switches the trans azobenzene dopants into cis, and the resulting cis-dopants with a twisted conformation become well dispersed in the liquid PCM (Fig. 1a, iii). We note that the temperature of the composite is maintained to be above 42 °C during the UV-charging process, which is enabled by simultaneous heating and UV absorption processes (see Methods section). This liquid composite is storing the fractional latent heat of the PCM (177 J g−1), that of trans azobenzene dopants (118 J g−1), as well as the fractional isomerization energy of the metastable cis azobenzene (116 J g−1). Surprisingly, the liquid state of the composite can be conserved through subsequent cooling to a temperature below the original T c (38 °C), while the latent thermal energy stored is fully maintained (Fig. 1a, iv). This striking heat storage ability of the composite is achieved by the metastable cis-dopants that can disrupt the packing of PCM molecules through steric repulsion and dipolar interactions, and require triggering to overcome the activation barrier for reverse isomerization to their ground-state trans form. Visible-light illumination rapidly switches the dopants and allows the PCM composite to crystallize and release the stored latent heat on-demand, recovering the original state of the composite (Fig. 1a, i).
The PCM composites before and after UV/thermal charging possess different phase-transition temperatures and scales of latent heat (Fig. 1b). Enthalpy and temperature changes, during the thermal storage and release cycle, are depicted as follows: (1) rise of temperature and enthalpy during the PCM melting, (2) isothermal enthalpy increase by UV illumination, (3) temperature and enthalpy decrease during cooling to an arbitrary temperature between T 1 and T 2, and (4) visible-light-triggered isothermal exothermic reaction. ΔT c, a figure of merit in this system, represents the degree of phase stabilization of the charged composite (PCM + cis-Azo) without losing heat. ΔH total, the expected exothermic energy density from the system, should be comparable to that of the pristine PCM for high-performance thermal storage applications. Figure 1c shows the basic structures of the PCM and the azobenzene dopants, selected for this proof-of-concept study, and we also explored other dopant derivatives that are systematically functionalized on the para-position of the azobenzene core to alter the intermolecular interactions in the resulting composites.
Optical control of PCM composite phase
Consistent with the schematic cycle shown in Fig. 1, the crystalline composite was partially molten when heated above the T m of the PCM, then charged by a UV (365 nm) lamp to become fully liquid, then able to be cooled below the T c of the pure PCM (38 °C), and was finally discharged by a blue (450 nm) LED light (Fig. 2a). The azobenzene dopant exhibits typical optical absorption properties of the trans and cis isomers, before and after UV illumination in solution (Fig. 2b)30, and the relative ratio of each isomer in the uncharged compound (94% trans) and in the UV-charged compound in the photostationary state (94% cis) was measured by1H NMR (Supplementary Fig. 1a, b). The efficiency and kinetics of solid-state trans → cis conversion of the azobenzene dopant in the PCM composites was also analyzed by 1H NMR (Supplementary Fig. 1c) which indicates the saturation of cis isomers at 90% after 1 h of charging. The dispersion of cis azobenzene in liquid PCM facilitates the uniform charging of the composite, and the time scale estimated for the dispersion is consistent with the experimental time scale for cis saturation (see Supplementary Note 1). T c of the charged composite was measured by differential scanning calorimetry (DSC), and compared to the uncharged composite (Fig. 2c). The charged composite crystallizes at 28 °C, followed by the crystallization of cis-Azo at 9 °C, while the uncharged counterpart exhibits the first solidification peak of trans-Azo at 48 °C, followed by the PCM crystallization at 38 °C. We note that the crystallization temperature of trans-Azo (60 °C measured as a pristine material) is significantly lowered in the PCM composites, as a result of the solvation by the liquid PCM molecules at temperatures higher than the PCM crystallization point. The melting point of trans-Azo (originally 73 °C) is also lowered, due to the solvation effect, and the degree of the changes in phase-transition temperatures can be variable, depending on the doping level in the composite and cooling rate.
Interestingly, T 1 and T 2 change significantly at varied doping levels (Fig. 2d) with the maximum ∆T c obtained at a doping level of 35 mol%. At low-doping levels (5–10 mol%), both T 1 and T 2 decrease slightly from the original T c of the PCM by a few degrees, resulting in negligible ∆T c (Supplementary Fig. 2a). Above 20 mol% doping, however, T 2 remains almost unchanged from 38 °C, and the azobenzene dopants crystallize separately at higher temperatures, as seen in Fig. 2c. ∆T c generally increases with a higher doping level but decreases at a doping level of 45 mol%. T 2 is fixed at 38 °C while T 1 increases up to 31 °C, and the charged composite shows a minor exothermic peak at 36 °C which can be assigned to the solidification of the trans-Azo dopant (Supplementary Fig. 2b). The relative crystallization enthalpy of the charged (ΔH 1) and uncharged (ΔH 2) composites was obtained by integrating the crystallization peaks (Fig. 2e). ΔH 1 and ΔH 2 are the sum of crystallization enthalpies of the PCM (∆H PCM) and dopant (∆H cis-Azo or ∆H trans-Azo) at relative weight fractions (χ between 0 and 1).
The measured ΔH 1 and ΔH 2 are well aligned with the calculated values, indicating that the dopants are mobile in the PCM medium and prone to aggregation, regardless of the isomeric state due to the strong dopant–dopant interactions. ∆H total is the heat released from liquid (cis) → solid (trans) transition of the composite, so it is described as
∆H iso is the isomerization enthalpy of the azobenzene dopant, measured by DSC during thermal reverse isomerization (cis → trans) occurring in the liquid state (Supplementary Fig. 3a), and ∆H iso of 116 J g−1 (46 kJ mol−1) is comparable and slightly improved from that of pristine azobenzene (41.4 kJ mol−1)31. A quantitative measurement of ΔH total was challenging due to the difficulty in decoupling the heat release from the composite and the heat absorption from the light source for optical triggering during the DSC measurement. However, assuming the complete cis → trans conversion, the expected heat release is considerable and increases with higher doping levels. When highly doped, ∆H PCM decreases, while the contributions of ∆H trans-Azo and ∆H iso increase. If it is 100% doped, the pristine azobenzene dopant has a potential to release 234 J g−1 of heat, but the requirement of heating it above its high T m (73 °C) for the solid-state charging induces the thermal reverse isomerization of the cis isomer, preventing the control over thermal storage. Also, UV illumination of azobenzene in the solid state without heating is ineffective as a result of steric confinement of aromatic groups in the crystalline lattice32. Thus, the design of PCM and the azobenzene composite has a unique advantage to realize thermal storage at temperatures above the relatively low T m of the PCM.
The dependence of ΔT c and ΔH on the doping level can be interpreted as a result of different degrees of nucleator formation and supercooling (Fig. 3a). At the low-doping level (5–10 mol%), both trans and cis dopants are well dispersed in the PCM and lower the T c of the composite by similar amounts, thus making ΔT c negligible (Fig. 3a, left). The low-doped composites are eutectic, showing no phase separation of PCM and dopants during solidification. However, with increased doping (20–35 mol%), the photo-switching action can influence ΔT c considerably due to the drastic differences in the aggregation dynamics of charged and uncharged dopants (Fig. 3a, center). The trans dopants first aggregate while the PCM composite is cooled and play a role as nucleating agents that facilitate the crystallization of PCM molecules on their surface. The addition of nucleators in the conventional PCMs for suppression of supercooling is well known, and the requirements for effective nucleators (high T m, an isomorphous structure to the PCM)33,34 are fulfilled by the properties of the trans azobenzene dopant aggregates. In contrast, cis dopants have strong interactions with the polar PCM molecules as well, leading to significant supercooling in the absence of nucleators, and the values of ΔT c are as high as 10 °C. If more dopants (45 mol%) are present, however, the solid-state UV charging of the composite is incomplete due to the relatively low fraction of the available molten PCM for solvating the trans-Azo dopants by overcoming the strong dopant–dopant interactions. (Supplementary Fig. 4) Therefore, the unconverted trans-Azo aggregates in the charged composites, although a minority of the total concentration, can act as nucleators and reduce the degree of supercooling and ΔT c (Fig. 3a, right).
X-ray diffraction patterns (Fig. 3b) show the prominent aggregation of trans dopants in the composites. The pattern of the uncharged composite shows both a distinct PCM and trans-Azo signatures, while that of the charged composite exhibits the major peaks of PCM and almost negligible peaks of trans-Azo that remains in the composite after solid-state charging (Supplementary Fig. 1c). Selective optical charging and discharging was conducted on composite films (Fig. 3c). The demonstration of local crystallization and liquefaction of the composite confirms that optical manipulation of the azobenzene conformation is indeed the key to phase transformation and thermal energy storage in the composites. The patterns can be easily removed by either UV/thermal charging for 1 h or by visible-light discharging for 30 s, and can be recycled repeatedly.
Intermolecular interactions controlling the phase change
In addition to dopant concentration, the cooling rate of UV/thermally charged composites also influences ΔT c, impacting T 1 more than T 2. T 2 is fixed around 38 °C, due to the facile formation of trans-Azo nucleators, while T 1 decreases significantly at fast cooling rates (Fig. 4a). When slowly cooled, the diffusion of cis dopants and the cis → trans conversion can reduce the impact of the cis dopants on disrupting the PCM arrangements, resulting in a higher T 1. In particular, the heating and cooling between 10 and 70 °C at the slowest rate of 1 °C min−1 exposes the metastable cis isomers to high-enough temperatures to enable thermal reverse isomerization over a considerable period of time, which was confirmed by the observation of trans-Azo aggregates through DSC measurements, leading to underestimated ∆T c values (3–4 °C).
Beyond concentration and the cooling rate, the chemical structures of photo-switching dopants and the relative strength of intermolecular interactions between dopants and that with PCM molecules can vary ΔT c in remarkably different ways (Fig. 4b). Compound 2 is a derivative of compound 1 with a decyloxy group substituted on azobenzene at the para-position, designed to increase the van der Waals interactions between alkyl chains present in both the PCM and dopants. Compound 2 exhibits the highest T c of 68 °C, indicating strong binding forces between the dopants through π–π stacking of aromatic cores and side packing between alkyl chains. Yet, compound 2 was observed to have a negligible impact on ΔT c compared to compound 1, because of the inefficient solid-state charging of trans aggregates in the PCM composites due to their strong packing (Supplementary Fig. 4). The charged composites show both trans and cis dopant crystallization peaks (around 60 and 10 °C, respectively), and the ratio of the trans/cis peak intensity increases with higher doping levels, confirming the difficulty in solid-state charging of strong aggregates.
Compound 3, on the other hand, possesses a bulky tert-butyl substitutent that significantly diminishes the π–π interactions between aromatic groups, helping to prevent the formation of nucleating agents in the composites. Interestingly, due to the sterically hindering nature of tert-butyl groups, the trans dopant can effectively disrupt the PCM alignment, even better than the cis isomer, as the negative value obtained for ΔT c implies. The cis dopants exert a similar degree of supercooling (by 5–6 °C) as the cis form of compound 1 at a doping level of 10 mol%, but the trans dopants induce a much larger supercooling (by 8–13 °C, over varied cooling rates). When the low numbers of dopants are dispersed in the PCM, the interactions between a dopant and the surrounding PCM molecules become the predominant factor that predicts the crystallization dynamics. However, at higher doping levels, dopant–dopant interactions and aggregations become increasingly important, as the formation of nucleators can greatly reduce the supercooling. Despite the repulsion between tert-butyl groups, the trans isomers crystallize at 44 °C (Supplementary Fig. 3b), whereas the cis isomers remain in the liquid state upon cooling down to −20 °C (Supplementary Figs. 3c, 5 and 6; Supplementary Movies 1 and 2)35, implying very little chance of forming any nucleator in the cooled composites. Indeed, the UV-charged composites are increasingly supercooled with more dopants, and the uncharged composites show a more slowly increasing degree of supercooling, competing with the nucleation process. At a doping level of 30 mol%, trans and cis isomers induce similar levels of supercooling, resulting in ΔT c closer to zero and similar ΔH 1 and ΔH 2 values (Supplementary Fig. 7). At 40 mol% doping, ΔT c is found to be positive, and ΔH 2 exceeds ΔH 1, as was the case for compound 1. The X-ray diffraction patterns (Supplementary Fig. 8) of low-doped (10 mol%) and high-doped (40 mol%) composites also corroborate these findings as follows: (1) higher impact of trans dopants on the PCM packing than that of cis isomers at a low level of doping and (2) larger disruption of PCM alignment by cis dopants at a high doping level.
We explored the binding energy (E b) between two molecules (either dopant or PCM) via ab initio calculations, and found that the dopant–dopant interaction is generally stronger than the PCM–PCM interaction, which explains the facile solidification of dopants in composites during the cooling process (Fig. 4c). We note that the binding energies of the cis dopants are generally overestimated due to the neglect of finite-temperature effects and ensemble environment. E b of compound 2 is much larger than that of other dopants, justifying its stronger tendency to aggregate and the negligible ΔT c of the composites. Consistent with the greater probability to form trans rather than cis aggregates, the binding between trans isomers is stronger than that between cis isomers for compound 1 and 2, even though the dynamic effects that may further reduce the stability of the cis crystal were not accounted for in the simulations. Upon functionalization with the tert-butyl group (compound 3), E b decreases in the trans while it increases in the cis dimer (configurations shown in Fig. 4d, compared to compound 1), which is in agreement with the higher concentration required for trans dopant aggregation observed in the experiment. In the low-doping region, both trans and cis dopants are dispersed, and thus, the interaction between an isolated dopant and the surrounding PCM molecules becomes the dominant factor that governs the crystallization dynamics. This situation was analyzed by considering E b between a trans isomer and a truncated PCM molecule in various energetically favorable configurations (Fig. 4e). In addition to the strongest binding between –COOH and ester groups, the results suggest that bound states are also feasible via the formation of hydrogen bonds with N atoms or van der Waals interactions between the –COOH group and aromatic rings (Fig. 4e). Compared to cis, an isolated trans may have a higher impact on disrupting PCM arrangement due to the planar structure that provides a larger space for binding on many different sites. The cis isomer, with such a bulky substituent, limits the interaction with another PCM molecule, for example, on the back side of the N = N group (the opposite configuration to Fig. 4e, top) because of the significant steric repulsion.
Finally, the stability of thermal energy storage in a UV/thermally charged composite (30 mol% of compound 1) was measured by 1H NMR analysis of the cis fraction and by monitoring solidification of the composite over a period of 24 h in the dark at the cooled temperature (36 °C, 6 °C below the T m) (Fig. 4f). The half-life of the cis dopant in such conditions was about 24 h, and the liquid phase was conserved for at least 10 h. When the cis ratio drops from 70% (10 h) to 65% (19 h), the solidification of the PCM was observed, which was also consistent with optical triggering experiments (Supplementary Fig. 9).
Energy efficiency analysis
The concept of this study is fundamentally different from that of conventional solar thermal fuels (STFs)36,37,38,39, or molecular solar thermal (MOST) systems22,40, which convert photon energy into stored thermal energy. Instead, here, we demonstrate a unique approach that uses the photon energy as a way to control the phase-transition properties of traditional thermal storage materials such as PCMs. The energy efficiency of this type of energy-storage system will depend on the thermal energy input from a high-temperature heat source (ΔH 2) and the released thermal energy at a lower temperature upon optical triggering (ΔH total). As described in equation (3), ΔH total is the sum of ΔH 2 and the reverse isomerization energy of azobenzene dopants (cis → trans), making it a greater value than the thermal storage density of each component (i.e., PCM molecule or the azobenzene dopant).
We note that the photon energy required for operating an azobenzene switch is considerable, given the low quantum yield (ca. 10%, different depending on the measurement conditions41,42) of its photoisomerization (trans → cis). For example, the PCM composite containing 30 mol% of azobenzene dopants requires UV (365 nm) photon energy of ca. 3.6 kJ per 1 gram of the composite for the photoinduced phase fixation, while the total heat storage in 1 gram of the composite is ca. 0.2 kJ, or about 5–6% of the input photon energy. This may seem to be inefficient, but the photon energy consumption for this system is significantly lower than that for conventional STFs. The energy-storage capacity of pristine azobenzene as an STF is 0.23 kJ g−1 31, while the input UV (365 nm) photon energy density is 18.0 kJ g−1 (1.3% efficiency). Other azobenzene derivatives that exhibit higher energy storage as a result of structural designs provide slightly improved efficiencies such as 2.7%32 and 3.0%43, assuming approximately 10% quantum yield. Utilizing azobenzene photoswitches as a minor component in the PCM composite gives rise to the relatively low demand for photon energy input, compared to that for STFs that consist of 100% photoswitches. Both STFs and photoswitchable PCMs would benefit from further development of high-quantum-yield photo-switching molecules to increase the energy efficiency. However, we note that abundant solar energy and radiation are expected to replace the current UV lamps, used for the experiments at this stage, as demonstrated on STFs by Saydjari and coworkers44.
We also note that this approach is fundamentally distinguished from the use of thermal insulation that is currently used for decreasing the cooling rate of thermally activated materials. While thermal insulation can reduce the loss of sensible heat, it cannot stop the spontaneous heat transfer between the thermally charged PCMs and the cooler surroundings (see Supplementary Fig. 10 for schematic energy diagrams comparing the two concepts) or the liquid-to-solid phase transition which leads to the loss of latent heat. In contrast, the photoswitchable PCM systems, which are able to still provide thermal storage even in the absence of thermal insulation, effectively preserve latent heat by changing the intrinsic properties (i.e., crystallization temperature) of the PCMs. As with traditional PCMs, thermal insulation can also be used with the photoswitchable PCMs to slow down the loss of sensible heat, but the advantage is the ability to hold on to the latent heat until it is released. Another difference between the two approaches is the triggerability of heat discharge. Optical triggering of the latent heat release from the photoswitchable PCMs is a newly introduced property to pristine PCMs with or without thermal insulation.
Based on these differences, we can compare the energy efficiency of azobenzene-doped PCMs and that of conventional PCMs with thermal insulation (Supplementary Note 2). As a result of gradual sensible heat loss through an insulation layer, conventional PCMs need external thermal energy input to maintain the liquid state at a high temperature, which leads to the efficiency drop over time (Supplementary Fig. 11). On the other hand, the efficiency of azobenzene-doped PCMs is determined by the UV photon energy input during the initial charging process that fixes the liquid state in the dark until a critical percentage of cis azobenzene undergoes reverse isomerization. As aforementioned, the use of photoswitches with higher quantum yields will significantly increase the energy efficiency that is constant over time in this system.
The goal of our work is to present a unique method to modify the thermodynamic properties of conventional PCMs and to explore the design criteria of the photo-switching dopants. For the potential applications and practical devices, multiple aspects of the system need to be optimized, and the potential challenges should be addressed. First, we envision a device structure that involves a container with windows and covers needed for the controlled light absorption and dark storage. Thermal energy from various waste heat sources, including solar heat, is indirectly transferred to the PCM composite using a heat exchanger, and a separate UV source (an LED or a gas-discharge lamp) will be used for the simultaneous azobenzene-charging process. The thermally activated PCM will be simply carried to a heat outlet at room temperature with the covers closed to enable dark storage. To trigger heat release, the covers will be opened to expose the liquid composite to ambient light or blue LED light for a faster release.
The PCM composite is designed to keep the stored latent heat even when it is cooled down to room temperature. Therefore, the facile heat loss through the glass windows or through the container without thermal insulation is considered as a part of the heat-transfer process to reach equilibrium with the cooler surroundings, while it would be a challenge in the pristine PCM system that solidifies at the original crystallization point. The common borosilicate glass that allows over 90% transmission of 365-nm UV and visible light will be suitable as the window material.
The implementation of a stirring or flowing system in the container can solve multiple potential challenges associated with the UV charging and visible-light discharging processes, including the fixed penetration depths of light, the initial phase separation of PCM and trans-Azo (during UV charging), and the scattering of visible light by the solidified portion of the PCM (during discharging).
In our system, the azobenzene dopants are suspended in the viscous liquid PCM when they are irradiated with UV, and solvated by the PCM as trans-to-cis conversion occurs. The dopants can diffuse in the viscous liquid phase of the PCM, which enables the facile charging of thick samples, similar to the complete charging of azobenzene solutions (in dichloromethane) in 20-mL vials that are 23-mm thick. The powder samples as shown in Fig. 2a are 100–200-μm thick, and the azobenzene dopants are successfully charged by UV irradiation (ca. 90%, Supplementary Fig. 1c). This indicates that the dynamics in the composite play an important role in increasing the actual penetration depth, despite the smaller calculated static penetration depth (23 µm, see Supplementary Note 3, Supplementary Fig. 12, and Supplementary Movie 3 for a detailed analysis). Therefore, we envision that the liquid PCM composite, once equipped with a stirrer or a flow system, will not be limited by the static light penetration depth or the initial phase separation, due to the uniform exposure to UV and the facile dissolution of trans-Azo aggregates. The stirring or flowing system will also effectively remove the scattering layer and disperse the nucleating sites in the bulk PCM during the discharging step, which allows for facile crystallization and propagation in a large-scale composite.
In order to demonstrate the concept at a larger scale, we devised an experiment where 3 g of a UV-charged PCM composite is optically triggered to release heat which is transferred to 1 g of water and raise its temperature effectively (Fig. 5). The lowering of T c of PCM from 38 to 29 °C by the addition of the azobenzene dopant and UV activation is clearly observed (Fig. 5a), and the triggering of crystallization above 29 °C by optical irradiation is demonstrated (Fig. 5b), in accordance with the milligram-scale DSC measurements and thin-film-patterning experiments. The heat release from the optically triggered composite is larger than that from the UV-charged composite in the dark, due to the additional contribution of dopant crystallization and azobenzene isomerization energy, consistent with our DSC measurements shown in Fig. 2. The longer crystallization process and the longer heating of water, despite the continuous and spontaneous heat loss to the cooler surroundings, indicate significant heat release from the composite and transfer to water. The impact of the blue light irradiation on the temperature of bulk materials, either PCM or water, was confirmed to be negligible, through a control experiment with pristine PCM and water. The LED lamp was placed 20 cm away from the PCM flask.
As shown in Fig. 5c, pristine PCM can heat water to a higher temperature for a shorter period, as a result of its higher T c (38–39 °C) and the faster heat loss to the surroundings at high temperatures. The crystallization process of pristine PCM is slower without contacting to a water container (Fig. 5d). In order to emphasize the impact of phase change and latent heat on water- heating dynamics, we conducted control experiments replacing the PCM by other substances which only transfer sensible heat to water within the temperature range of study. Octadecane was chosen as a type of paraffin which has a similar thermal conductivity and heat capacity to tridecanoic acid but presents a low T c of 28 °C (Fig. 5e), and water as a common heating medium with a high heat capacity (Fig. 5f). In both cases, the heated water cools down rapidly, in contrast to water in a solidifying PCM composite bath, demonstrating the significant advantage of PCMs over heated liquid as a heating medium. Over 5 times longer heating of water enabled by the light-triggered phase change than by the sensible heat transfer from other heated fluids shows the significance and practicality of latent heat storage and release.
Finally, the long-term stability and reversibility of the photo-switching composites needs to be addressed. High thermophysical stability of the azobenzene dopant (compound 1) at temperatures up to 200 °C and the optical cycling stability over 100 cycles of charging and discharging for over 50 h were probed (Supplementary Fig. 13), and the invariable morphology of the composite after optical discharging was analyzed by the Fourier transforms of optical microscope images (Supplementary Fig. 14). Further X-ray diffraction studies, however, indicate that optically induced fast crystallization can lead to less aggregation and incomplete cis-to-trans conversion, consistent with the molar fraction analysis of the cis isomer during optical discharging (Supplementary Fig. 9). Although crystallinity of the PCM composite is slightly changed from the starting material after the initial optical discharging, the morphology and crystallinity of the composite in the subsequent cycles of UV charging and visible-light discharging will be fully reversible.
In summary, a unique method is demonstrated to control the intermolecular interactions between phase-change materials and photochromic dopants for thermal energy storage and release in the composites by optical switching. This simple approach provides the foundation to add a functionality to conventional heat-storage materials and potentially to various other types of PCMs including inorganic materials by employing suitable photoswitches that can interact with relative PCMs effectively. This proof of concept may provide insights into thermal energy management for a wide range of potential applications such as waste heat recycling, solar thermal collection, and smart temperature systems for buildings.
Tridecanoic acid, oxalyl chloride, and the azobenzene starting materials were purchased from Sigma-Aldrich and were used without further purification. Dichloromethane, tetrahydrofuran, dimethylforamide, and methanol were purchased from VWR and were used as received.
Synthesis of azobenzene dopants
To a solution of tridecanoic acid (385 mg, 1.8 mmol) in dichloromethane (5 mL), oxalyl chloride (231 µL, 2.7 mmol) was added dropwise at room temperature and stirred for 10 min. A catalytic amount (a drop) of dimethylformamide was added to the mixture, and the solution was stirred for 3 h generating CO2 (g), CO (g), and HCl (g) through a bubbler. The reaction mixture was dried under reduced pressure (50 mTorr) for 2 h to obtain tridecanoic acid chloride (yellow oil) which was used for the next step without further purification. The acid chloride (417 mg, 1.8 mmol) was dissolved in dry THF (5 mL) which was added dropwise to the mixture of 4-phenylazophenol (534 mg, 2.7 mmol) and triethylamine (1.1 mL, 8.1 mmol) in dichloromethane (50 mL). After the gas evolution stopped, the mixture was stirred overnight, and the solvent was evaporated to a reduced volume (5 mL). Methanol (10 mL) was added to the reaction mixture to precipitate a yellow powder that was filtered, rinsed with methanol, and dried under reduced pressure. The clean product, compound 1 (567.4 mg), was obtained with 80.1% yield.
Compounds 2 and 3 were synthesized with different phenylazophenol precursors, 4-(4-decyloxyphenylazo)phenol and 4-(4-tert-butylphenylazo)phenol, and were obtained at 89.1% and 62.5% yields, respectively. The 1H and 13C NMR spectra and the structural information including HRMS of the compounds can be found in Supplementary Figs. 15–20 and Supplementary Methods.
Sample preparation and charging/discharging procedures
The composites were prepared by dissolving the relative fractions of the PCM and azobenzene dopants mixed in dichloromethane which was evaporated at 40 °C under nitrogen flow. The solid samples were then transferred to glass substrates and were heated at 43 °C while being irradiated by a UV lamp (365 nm, 100 W) that was placed 25 cm above the samples. The UV-charging station was covered by a container and aluminum foil to block ambient light exposure. After 1 h of charging, the samples were transferred to DSC pans in the dark for measurements. For discharging, the samples were illuminated by a blue LED lamp (450–460 nm, 15 LED chips, 12 W) placed 10 cm above the samples at 36 °C for 30 s. For the patterning experiments (Fig. 3c), the composites were UV/thermally charged on glass substrates, and the liquefied samples were pressed under another glass slide to make films. For solution-state charging, the azobenzene derivatives were dissolved in dichloromethane and illuminated by the UV lamp while being stirred at room temperature. The charged solutions were then dried under reduced pressure in the dark to prepare DSC samples.
1H and 13C NMR spectra were taken on Varian Inova-500 spectrometers. Chemical shifts were reported in ppm and referenced to residual solvent peaks (CD2Cl2: 5.33 ppm for 1H, 53.84 ppm for 13C, CDCl3: 7.26 ppm for 1H, and 77.16 ppm for 13C). Bruker Daltonics APEXIV 4.7 Tesla Fourier transform ion cyclotron resonance mass spectrometer was used for high-resolution mass determination with an electrospray ionization (ESI) source. UV–Vis absorption spectra were obtained using a Cary 60 UV–Vis spectrophotometer (Agilent Technologies) in a 10-mm pathlength quartz cuvette. DSC analysis was conducted on a Q series DSC Q20 (TA Instruments) with the RCS40 component. Powder X-ray diffraction (PXRD) patterns were recorded on Bruker D8 Discover diffractometer using nickel-filtered Cu-Kα radiation (λ = 1.5418 Å) with an accelerating voltage and current of 40 kV and 40 mA, respectively. Samples for PXRD were prepared by placing a thin layer of the appropriate material on a zero-background silicon crystal plate.
Standard ab initio calculations within the framework of density-functional theory (DFT) were performed to optimize the geometry and calculate the binding energies of molecular dimers with various configurations, using the Vienna Ab Initio Simulation Package (VASP v5.4)45. Plane-wave and projector-augmented-wave (PAW)-type pseudopotentials46 were employed with a 400 eV kinetic-energy cutoff and the GGA-PBE exchange-correlation functional47. Van der Waals interactions were included by the DFT-D2 method of Grimme. A 20 Å vacuum along the direction involving π–π stacking and a 15 Å vacuum for all other directions were constructed to avoid artificial interactions between periodic images. The structures were relaxed until all forces were smaller than 0.02 eV Å−1.
In order to overcome the challenge of computing long molecules with a large vacuum, the truncated molecules with short tails containing only 4 C atoms were used as representatives in all simulations. This approximation is justified by considering the PCM dimers with various alkyl chains, wherein the binding energy increases linearly with increasing tail length at the rate of 0.055 eV per CH2 unit. Then, the final binding energies between stacking dimers as shown in Fig. 4d were obtained by the summation over the binding energy of truncated dimers and the estimated contributions from alkyl chains based on the above relation. For the exploration of the possibility to bind an individual dopant with multiple PCMs at a low-doping level (Fig. 4e), the van der Waals interactions from long tails have been excluded because most of the surrounding PCMs will not be able to ideally stack with the dopant.
The data that support the findings of this study are available from the corresponding author upon reasonable request.
Sandnes, B. & Rekstad, J. Supercooling salt hydrates: Stored enthalpy as a function of temperature. Sol. Energy 80, 616–625 (2006).
Kenisarin, M. M. High-temperature phase change materials for thermal energy storage. Renew. Sustainable Energy Rev. 14, 955–970 (2010).
Baetens, R., Jelle, B. P. & Gustavsen, A. Phase change materials for building applications: A state-of-the-art review. Energy Build. 42, 1361–1368 (2010).
Rathod, M. K. & Banerjee, J. Thermal stability of phase change materials used in latent heat energy storage systems: A review. Renew. Sustainable Energy Rev. 18, 246–258 (2013).
Gur, I., Sawyer, K. & Prasher, R. Searching for a better thermal battery. Science 335, 1454–1455 (2012).
Pielichowska, K. & Pielichowski, K. Phase change materials for thermal energy storage. Prog. Mater. Sci. 65, 67–123 (2014).
Tokoro, H. et al. External stimulation-controllable heat-storage ceramics. Nat. Commun. 6, 7037 (2015).
Kousksou, T., Jamil, A., El Rhafiki, T. & Zeraouli, Y. Paraffin wax mixtures as phase change materials. Sol. Energy Mater. Sol. Cells 94, 2158–2165 (2010).
Sari, A. & Bicer, A. Thermal energy storage properties and thermal reliability of some fatty acid esters/building material composites as novel form-stable PCMs. Sol. Energy Mater. Sol. Cells 101, 114–122 (2012).
Aydin, A. A. & Okutan, H. High-chain fatty acid esters of myristyl alcohol with odd carbon number: Novel organic phase change materials for thermal energy storage-2. Sol. Energy Mater. Sol. Cells 95, 2417–2423 (2011).
Feng, L. L. et al. The shape-stabilized phase change materials composed of polyethylene glycol and various mesoporous matrices (AC, SBA-15 and MCM-41). Sol. Energy Mater. Sol. Cells 95, 3550–3556 (2011).
Solé, A. et al. Stability of sugar alcohols as PCM for thermal energy storage. Sol. Energy Mater. Sol. Cells 126, 125–134 (2014).
Kenisarin, M. M. Thermophysical properties of some organic phase change materials for latent heat storage. A review. Sol. Energy 107, 553–575 (2014).
Zhang, J., Zou, Q. & Tian, H. Photochromic materials: More than meets the eye. Adv. Mater. 25, 378–399 (2013).
Russew, M.-M. & Hecht, S. Photoswitches: From molecules to materials. Adv. Mater. 22, 3348–3360 (2010).
Wojtecki, R. J., Meador, M. A. & Rowan, S. J. Using the dynamic bond to access macroscopically responsive structurally dynamic polymers. Nat. Mater. 10, 14–27 (2011).
Klajn, R. Spiropyran-based dynamic materials. Chem. Soc. Rev. 43, 148–184 (2014).
van Oosten, C. L., Bastiaansen, C. W. M. & Broer, D. J. Printed artificial cilia from liquid-crystal network actuators modularly driven by light. Nat. Mater. 8, 677–682 (2009).
Beharry, A. A. & Woolley, G. A. Azobenzene photoswitches for biomolecules. Chem. Soc. Rev. 40, 4422–4437 (2011).
Jochum, F. D. & Theato, P. Temperature- and light-responsive smart polymer materials. Chem. Soc. Rev. 42, 7468–7483 (2013).
Zhao, Y. et al. Small-molecule-directed nanoparticle assembly towards stimuli-responsive nanocomposites. Nat. Mater. 8, 979–985 (2009).
Moth-Poulsen, K. et al. Molecular solar thermal (MOST) energy storage and release system. Energy Environ. Sci. 5, 8534–8537 (2012).
Fihey, A., Perrier, A., Browne, W. R. & Jacquemin, D. Multiphotochromic molecular systems. Chem. Soc. Rev. 44, 3719–3759 (2015).
Kobatake, S., Takami, S., Muto, H., Ishikawa, T. & Irie, M. Rapid and reversible shape changes of molecular crystals on photoirradiation. Nature 446, 778–781 (2007).
Jiang, H. Y., Kelch, S. & Lendlein, A. Polymers move in response to light. Adv. Mater. 18, 1471–1475 (2006).
Liu, N. G. et al. Photoregulation of mass transport through a photoresponsive azobenzene-modified nanoporous membrane. Nano Lett. 4, 551–554 (2004).
Bond, A. D. On the crystal structures and melting point alternation of the n-alkyl carboxylic acids. N. J. Chem. 28, 104–114 (2004).
Gbabode, G. et al. Structures of the high-temperature solid phases of the odd-numbered fatty acids from tridecanoic acid to tricosanoic acid. Chem. Eur. J. 13, 3150–3159 (2007).
Ueki, T. et al. UCST phase transition of azobenzene-containing random copolymer in an ionic liquid. Macromolecules 44, 6908–6914 (2011).
Bléger, D. & Hecht, S. Visible-light-activated molecular switches. Angew. Chem. Int. Ed. 54, 11338–11349 (2015).
Corruccini, R. J. & Gilbert, E. C. The heat of combustion of cis- and trans-azobenzene. J. Am. Chem. Soc. 61, 2925–2927 (1939).
Han, G. D. et al. Photon energy storage materials with high energy densities based on diacetylene-azobenzene derivatives. J. Mater. Chem. A 4, 16157–16165 (2016).
Lane, G. A. Phase change materials for energy storage nucleation to prevent supercooling. Sol. Energy Mater. Sol. Cells 27, 135–160 (1992).
Mehling, H. & Cabeza, L. F. Heat and Cold Storage with PCM: An up to Date Introduction Into Basics and Applications (Springer, Berlin Heidelberg, 2008).
Zhou, H. et al. Photoswitching of glass transition temperatures of azobenzene-containing polymers induces reversible solid-to-liquid transitions. Nat. Chem. 9, 145–151 (2016).
Kolpak, A. M. & Grossman, J. C. Azobenzene-functionalized carbon nanotubes as high-energy density solar thermal fuels. Nano Lett. 11, 3156–3162 (2011).
Kucharski, T. J. et al. Templated assembly of photoswitches significantly increases the energy-storage capacity of solar thermal fuels. Nat. Chem. 6, 441–447 (2014).
Feng, Y. et al. Covalent functionalization of graphene by azobenzene with molecular hydrogen bonds for long-term solar thermal storage. Sci. Rep. 3, 3260 (2013).
Luo, W. et al. A high energy density azobenzene/graphene hybrid: a nano-templated platform for solar thermal storage. J. Mater. Chem. A 3, 11787–11795 (2015).
Dreos, A. et al. Exploring the potential of a hybrid device combining solar water heating and molecular solar thermal energy storage. Energy Environ. Sci. 10, 728–734 (2017).
Yan, Y., Wang, X., Chen, J. I. L. & Ginger, D. S. Photoisomerization quantum yield of azobenzene-modified DNA depends on local sequence. J. Am. Chem. Soc. 135, 8382–8387 (2013).
Zimmerman, G., Chow, L.-Y. & Paik, U.-J. The photochemical isomerization of azobenzene1. J. Am. Chem. Soc. 80, 3528–3531 (1958).
Ishiba, K. et al. Photoliquefiable ionic crystals: A phase crossover approach for photon energy storage materials with functional multiplicity. Angew. Chem. Int. Ed. 54, 1532–1536 (2015).
Saydjari, A. K., Weis, P. & Wu, S. Spanning the solar spectrum: Azopolymer solar thermal fuels for simultaneous UV and visible light storage. Adv. Energy Mater. 7, 1601622 (2017).
Kresse, G. & Furthmuller, J. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set. Phys. Rev. B 54, 11169–11186 (1996).
Blochl, P. E. Projector augmented-wave method. Phys. Rev. B 50, 17953–17979 (1994).
Perdew, J. P., Burke, K. & Ernzerhof, M. Generalized gradient approximation made simple. Phys. Rev. Lett. 77, 3865–3868 (1996).
Kumar, G. S. & Neckers, D. C. Photochemistry of azobenzene-containing polymers. Chem. Rev. 89, 1915–1925 (1989).
Siewertsen, R. et al. Highly efficient reversible Z−E photoisomerization of a bridged azobenzene with visible light through resolved S1(nπ*) absorption bands. J. Am. Chem. Soc. 131, 15594–15595 (2009).
Goto, M. & Asada, E. The crystal-structure of the a’-form of tridecanoic acid. Bull. Chem. Soc. Jpn 53, 2111–2113 (1980).
Materials and resources funding for this project was provided by the Tata Center at MIT Energy Initiative (Award No. 021447–00033). The authors thank Ms. Sarah Sunah Park and Prof. Mircea Dincă in the Department of Chemistry at MIT for PXRD measurements. We acknowledge Ms. Farnaz Niroui, Mr. Mayuran Saravanapavanantham, and Prof. Vladimir Bulović in the Department of Electrical Engineering and Computer Science at MIT for the access and the acquirment of optical microscope images and videos. We thank Ms. Li Li at MIT DCIF (Department of Chemistry Instrumentation Facility) for high-resolution mass determination. We thank Dr. David Zhitomirsky for significant discussions on the experimental designs.
The authors declare no competing financial interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Han, G.G.D., Li, H. & Grossman, J.C. Optically-controlled long-term storage and release of thermal energy in phase-change materials. Nat Commun 8, 1446 (2017). https://doi.org/10.1038/s41467-017-01608-y
Solvent-free synthesis of PEG modified polyurethane solid-solid phase change materials with different Mw for thermal energy storage
Colloid and Polymer Science (2021)
Journal of Thermal Analysis and Calorimetry (2021)
Cellulose nanofiber/melanin hybrid aerogel supported phase change materials with improved photothermal conversion efficiency and superior energy storage density
Scientific Reports (2020)
A state of the art on solar-powered vapor absorption cooling systems integrated with thermal energy storage
Environmental Science and Pollution Research (2020)