Abstract
Isotactic ultra-high molecule weight polypropylene (UHMWPP) composites filled with multi-wall carbon nanotubes (MWNTs), vapor growth carbon fibers (VGCFs) and short carbon fibers (CFs) were prepared by gelation/crystallization from solutions, in which these aspect ratios of MWNTs, VGCFs and CFs chosen were 500–1000, 50–300 and 5–20, respectively. The thermal, electrical and mechanical properties of these composites were studied in terms of their aspect ratios of the three kinds of fillers. The admixture of the three kinds of carbon filler provided better improvement of thermal property in comparison with neat UHMWPP, and the effect was the most significant for the admixture of MWNTs with the highest average aspect ratio. The electrical conductivity by the admixture of carbon fillers was also sensitive to the aspect ratio. Namely, the electrical conductivity of undrawn UHMWPP-MWNT composite film was the highest, when the filler content of the composites was the same. The conductivities of UHMWPP-VGCF and UHMWPP-CF composites decreased drastically by elongation up to 5 times (λ=5), while the conductivity of UHMWPP-MWNT maintained ca. 10−3 S/cm at λ=5 but further elongation up to λ=20 caused a gradual decrease of the conductivity. Young’s modulus of the UHMWPP-VGCF composites was higher than that of neat UHMWPP films in undrawn and drawn states, while that of UHMWPP-MWNT composites became lower when the composite with 3 wt % MWNT content was elongated up to λ=20. These phenomena indicated that a number of entanglement points of MWNTs within the composite assure electric channels in drawn state but hamper the smooth orientation of UHMWPP chains.
Similar content being viewed by others
Article PDF
References
S. Kumar, H. Doshi, M. Srinivasarao, J. O. Park, and D. A. Schiraldi, Polymer, 43, 1701 (2002).
S. A. Gordeyev, J. A. Ferreira, C. A. Bernardo, and I. M. Ward, Mater. Lett., 51, 32 (2001).
C. F. Ou, Eur. Polym. J., 38, 467 (2002).
E. Assouline, A. Lustiger, A. H. Barber, C. A. Cooper, E. Klein, and E. Wachtel, J. Polym. Sci., Part B: Polym. Phys., 41, 520 (2003).
S. Subramoney, Electrochem. Soc. Interface, 18, 34 (1999).
J. I. Paredes, A. Martínez-Alonso, and J. M. D. Tascón, Carbon, 39, 1575 (2001).
M. Endo, Y. A. Kim, T. Hayashi, K. Nishimura, T. Matusita, and K. Miyashita, Carbon, 39, 1287 (2001).
D. D. L. Chung, Carbon, 39, 1119 (2001).
C. J. Lee and J. Park, Carbon, 39, 1891 (2001).
R. Maragoni, P. Serp, R. Feuer, Y. Kihn, P. Kalck, and C. Vahlas, Carbon, 39, 443 (2001).
L. Ci, B. Wie, J. Liang, J. Liang, C. L. Xu, and D. H. Wu, Carbon, 39, 329 (2001).
K. Lozano and E. V. Barrera, J. Appl. Polym. Sci., 79, 125 (2001).
R. Andrews, D. Jacques, A. M. Rao, T. Rantell, F. Derbyshire, and Y. Chen, Appl. Phys. Lett., 75, 1329 (1999).
F. W. J. Hattum, C. A. Bernardo, J. C. Finegan, G. G. Tibbetts, R. L. Alig, and M. L. Lake, Polym. Compos., 20, 683 (1999).
D. Qian, E. C. Dickey, R. Andrews, and T. Rantell, Appl. Phys. Lett., 76, 2868 (2000).
M. S. P. Shaffer and A. H. Windle, Adv. Mater., 11, 937 (1999).
R. Haggenmueller, H. H. Gommans, A. G. Rinzler, J. E. Fischer, and K. I. Winey, Chem. Phys. Lett., 330, 219 (2000).
L. Jin, C. Bower, and O. Zhou, Appl. Phys. Lett., 73, 1197 (1998).
J. Dupire and J. Michel, Fina Research SA., European patent 1,054,036 AL, 2000.
L. Valentini, J. Biagiotti, J. M. Kenny, and S. Santucci, Compos. Sci. Technol., 63, 1149 (2003).
A. Amash and P. Zugenmaier, J. Appl. Polym. Sci., 63, 1143 (1997).
M. A. López Manchado, L. Valentin, J. Biagiotti, and J. M. Kenny, Carbon, 43, 1499 (2005).
M. Matsuo, C. Sawatari, and T. Nakano, Polym. J., 18, 759 (1986).
C. Sawatari and M. Matsuo, Macromolecules, 22, 2968 (1989).
D. S. Bethune, Phys. Rev. B: Condens. Matter, 323, 90 (2002).
E. Borowiak-Palen, T. Pichler, X. Liu, M. Knupfer, A. Graff, and O. Jost, Chem. Phys. Lett., 363, 567 (2002).
G. Natta and P. Corradini, Nuovo Cimento Suppl., 15, 40 (1960).
G. Natta, Macomol. Chem., 35, 94 (1960).
J. A. Sauer, D. R. Morrow, and G. C. Richardson, J. Appl. Phys. 36, 3017 (1965).
M. Kojima, J. Polym. Sci., Part A-2, 5, 597 (1967).
N. G. McCrum, B. E. Read, and G. Williams, “Anelastic and dielectric effects in polymeric solids,” John Wiley and Sons, London, 1967.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Jiang, X., Bin, Y., Kikyotani, N. et al. Thermal, Electrical and Mechanical Properties of Ultra-high Molecular Weight Polypropylene and Carbon Filler Composites. Polym J 38, 419–431 (2006). https://doi.org/10.1295/polymj.38.419
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1295/polymj.38.419
Keywords
This article is cited by
-
Progress in MgCl2 supported Ziegler-Natta catalyzed polyolefin products and applications
Journal of Polymer Research (2021)
-
Investigations on the interactions between Li-TFSI and glass fibers in the ternary PP/GF/Li-TFSI composites
Chinese Journal of Polymer Science (2018)
-
A study of the layered microstructure and electrical resistivity of an injection-molded metallic fiber-filled polymer composites
Polymer Journal (2012)
-
Effect of the processing of injection-molded, carbon black-filled polymer composites on resistivity
Polymer Journal (2011)