Abstract
Laser cooling has given a boost to atomic physics throughout the last 30 years, as it allows one to prepare atoms in motional states, which can only be described by quantum mechanics. Most methods rely, however, on a nearresonant and cyclic coupling between laser light and welldefined internal states, which has remained a challenge for mesoscopic particles. An external cavity may compensate for the lack of internal cycling transitions in dielectric objects and it may provide assistance in the cooling of their centreofmass state. Here we demonstrate cavity cooling of the transverse kinetic energy of silicon nanoparticles freely propagating in high vacuum (<10^{−8} mbar). We create and launch them with longitudinal velocities down to v≤1 m s^{−1} using laserinduced ablation of a pristine silicon wafer. Their interaction with the light of a highfinesse infrared cavity reduces their transverse kinetic energy by up to a factor of 30.
Similar content being viewed by others
Introduction
Pioneering achievements in Doppler cooling^{1,2}, polarization gradient cooling^{3} or subrecoil laser cooling^{4,5} of atoms, and also the recently demonstrated Doppler cooling of molecules^{6}, have opened rapidly growing fields of research in atomic and molecular physics. The accessibility of ultralow temperatures allows one to study even novel states of quantum degenerate matter^{7}. In contrast to that, laser cooling of macromolecules or nanoparticles has been precluded by the lack of suitably narrow, closed optical transitions, which could be used to exchange momentum between light and matter. Offresonant laser fields in highfinesse cavities may, however, be used to circumvent this restriction. Nanoparticles can then be cooled by applying an effective Sisyphus process, which forces them to climb in a sinusoidal optical potential, which is always higher in the ascent than in the descent. In practice, the potential hill arises from the dipole interaction between the particle’s polarizability and the electric field of the cavity’s standing light wave. Its amplitude is modulated by the particle itself when it crosses the nodes and antinodes of the cavity mode, and therefore changes the coupling of the field to the refractive index of the polarizable particle.
The original idea of cavity cooling^{8,9} has already been realized with atoms^{10}, ions^{11} and atomic ensembles^{12}, even to below the recoil limit^{13}. Such experiments benefit from advanced preparation methods and resonant optical forces, which are available for atoms. In contrast to that, the manipulation of mesoscopic particles cannot profit from any internal resonance. On the other hand, nonresonant light forces are nonsatiating in nature and one can benefit from high optical intensities for cooling and from high scattering rates to gain detailed insight into the cavitycooling process. Several groups have started to load silica (SiO_{2}) micro or nanoparticles into buffer gasassisted optical dipole traps to successfully subject them to optical cooling^{14,15,16}. In contrast to that, we here demonstrate efficient transverse cavity cooling of pure and freely propagating silicon (Si) nanoparticles in a highvacuum environment.
Results
Optical setup
The outline of our experiment is shown in Fig. 1. We generate pure silicon nanoparticles in situ by directing a pulsed focused laser beam onto the back side of a clean silicon wafer. The particles emerging from the front side travel upwards against gravity and interact with the standing light wave inside the highfinesse cavity. A fibre laser operating at λ=1,560 nm seeds the fundamental TEM_{00} cavity mode. Its frequency is modulated via the doublepass acoustooptic modulator AOM1 and the locking signal is derived from the cavity mirror’s birefringence^{17}. A part of the modulated laser light is split off, frequency modulated by 40 MHz in AOM2 and mixed with the light that is transmitted through the resonator on photodiode D3. The resulting 40 MHz beating signal is digitized to extract the phase difference between the two beams.
In parallel, the time evolution of the intracavity power is monitored via the intensity captured by D2 behind the cavity mirror R2. The photodiode D1, positioned under right angle to both the cavity axis and the polarization of the incident laser beam, is used to record the scattered light when a silicon particle passes the cavity. The detector is dominantly sensitive to the dipole radiation pattern, which reveals details about the coupling strength between the transiting particle and the cavity field.
Cooling principle
A subwavelength object of polarizability α experiences the optical potential V_{opt}=−ħU_{0}a^{2}f^{2}(x), where f(x) describes the intracavity mode function and a is the field amplitude. The particle effectively increases the cavity length due to its index of refraction and it shifts the cavity resonance by U_{0}f^{2}(x), where U_{0}=αω_{L}/2∈_{0}V, V is the mode volume and ω_{L} is the angular frequency of the laser^{18}. Because of the cavity’s high finesse, even a small length change leads to a significant phase shift of the cavity field. If the incident laser beam of frequency ω_{L} is redshifted with respect to the cavity resonance ω_{C} (ω_{L}−ω_{C}<0) any normaldispersive particle (highfield seeker, index of refraction n>1) will tune the cavity resonance closer to the laser frequency and increase the intracavity power.
When a particle moves along the cavity mode, it creates a timedependent phase shift and intensity modulation. The intensity is maximal when the particle leaves an antinode of the optical lattice and is minimal when it moves towards it. Therefore, the particle gains less energy when it runs downhill than it loses while running uphill. This Sisyphustype cooling^{8} is most efficient when the field maxima coincide with the steepest slope of the coupling curve, which is satisfied for particles with a Doppler shift of kv≈Δ. To achieve the maximum intensity change per phase change, the cavity is detuned by one resonator line width κ to Δ≈−κ.
Particle launch
One of the grand questions in nanoparticle cavity cooling, in comparison with the case of atoms, is how to prepare slow neutral particles in the first place. We use laserinduced thermomechanical stress on a pristine surface to generate and release clean silicon nanoparticles under highvacuum conditions. The scanning electron micrograph (SEM) image in Fig. 2a shows a prototypical nanoparticle that was released from the front side of a silicon wafer when its back side was irradiated by pulsed laser light. This method generates objects of varying diameters and shapes, ranging from spheres of <100 nm across to arbitrarily shaped fragments well beyond 1 μm. An SEM image of the wafer’s front surface (Fig. 2b) corroborates the proposed mechanism of particle formation: microscopic cracks appear as a result of the laserinduced stress^{19}. Here we post select the smaller fraction of particles, as objects with a radius above 200 nm will average over the standing wave potential and see reduced cooling forces^{20}.
Particle dynamics and cooling
The light in photodiode D2 measures the intracavity power I_{c}(t) and, therefore, also the expected optical forces. The intensity I_{s}(x(t)) scattered into photodiode D1 is a measure for the light intensity at the particle position. We derive a normalized scattering coefficient S_{N}(t)≡(I_{s}/I_{c})/max(I_{s}/I_{c}) and plot it in Fig. 3a. It is an intensityindependent measure for the scattering probability, which contains information about the cooling process. It relates to the cavity mode function via S_{N}(t)=sin^{2}(kz(t))exp(−2x^{2}(t)/w^{2}), where w is the mode waist. We can extract the particle position z(t) from S_{N}(t). When the particle passes the cavity with the velocity v_{x}, we expect a Gaussian envelope of S_{N}(t) with an e^{−1/2} halfwidth of w/v_{x}. From this, we deduce an x velocity of v_{x}=0.7 m s^{−1} for Fig. 3a.
It is possible to reconstruct the particle trajectory with good reliability^{21} to illustrate cooling and temporary channelling, as shown in Fig. 3. In the beginning of the Gaussian envelope, the particle is almost unaffected by the weak optical potential and it travels under a small angle to the vertical direction. One expects a sinusoidal modulation of S_{N}(t) with a period of T=λ/2v_{z}, where v_{z} is the initial velocity along the cavity axis. A maximum in S_{N}(t) reveals the particle’s passage through an antinode of the standing wave. When the nanosilicon approaches the cavity centre along the x axis, its transverse velocity v_{z} is repeatedly reduced by the desired intracavity Sisyphus effect. Once the particle’s kinetic energy has fallen below the optical potential, the silicon ball is channelled vertically between two standingwave nodes. The first velocity inversion, that is, the onset of channelling, can be identified with a first local nonzero minimum of S_{N}(t). Near the first trapping point (i in Fig. 3e), the oscillation period is particularly long, as the particle also explores the anharmonic part of the sinusoidal potential. On its way towards the centre of the Gaussian envelope, the particle experiences an increasing trap depth and it is further cooled. Therefore, the spatial excursions are then limited to the harmonic part of the well, resulting in faster oscillations.
The oscillation amplitude of the channelled particle is a measure for its transverse kinetic energy and the cooling force is active as long as the intensity maximum lags behind the maximum of S_{N}(t). However, the energy loss per cycle decreases, as the particle now remains bound to regions of similar coupling. The overall energy loss of the nanosilicon leads to a clearly visible asymmetry in S_{N}(t). The particle enters the cavity with a horizontal velocity of v_{z}=22.8(1) cm s^{−1} and leaves it with v_{z}=4.0(2) cm s^{−1}. This corresponds to a reduction in the transverse kinetic energy by a factor of more than 30.
While the particle moves along the standingwave it modulates the cavity phase (Fig. 3c). From the amplitude of this modulation, we can extract an effective coupling frequency U_{z}=2.3(4)κ. Because of an uncertainty in the y position, field averaging caused by the particle’s finite size and possibly an anisotropic shape, U_{z} is a lower bound for the maximal coupling frequency U_{0}. To estimate U_{0} and to derive a particle size, we measure the trapping frequency f_{trap}, while the particle is channelled. We find that the measured trapping frequency of f_{trap}=145 kHz corresponds to a silicon sphere with a radius of about 150 nm (2 × 10^{10} amu, polarizability of 4π∈_{0} × 2.7 × 10^{9} Å^{3}, N=7 × 10^{8} atoms), which misses the cavity centre by about 0.4 waists.
Figure 4a shows the normalized scattering signal S_{N}(t) of a second nanoparticle in transit through the cavity. We find a forward velocity of v_{x}=2.1 m s^{−1}. The initial transverse velocity is v_{z,in}=41(2) cm s^{−1}. Although the particle travels through the mode, the phase and intensity of the cavity lags behind S_{N}, which leads to cooling (see Fig. 4b). Contrary to the particle of Fig. 3, this second particle runs over the standing wave, while leaving the cavity mode. Hence, the final transverse velocity can be measured directly as before and we obtain v_{z,out}=20(1) cm s^{−1}. The reduction of the transverse kinetic energy by a factor of 4.2(2) is smaller than for the particle in Fig. 3. This can be explained by the higher forward velocity and the shorter interaction time with the cavity mode.
Discussion
The kinetic energy associated with the forward velocity is at least ten times larger than that related to the transverse component in our examples. Therefore, the forward velocity is less affected by the optical potential. In addition, electronic feedback suppresses intensity modulations on the timescale of the particle’s transit through the Gaussian waist but not during the particle’s passage between two cavity nodes. In summary, we do not expect a deviation from the overall Gaussian envelope. One may consider additional forces along the cavity axis different from the one mediated by the standing light wave. They are, however, estimated to be negligible in our case: an asymmetry of the dipole forces might be expected in z direction because of the asymmetric cavity configuration and the fact that the particles transit the field z=1.5 mm offcentre, that is, at half the cavity length. The z gradient of the laser field scales with the Rayleigh length as for z<<z_{R}=8 mm. Compared with the dipole forces that are related to the sinusoidal part of the cavity mode, this force asymmetry is smaller by a factor z/k=5 × 10^{−6}. For highly transparent subwavelength particles, the net radiation pressure forces in a standing light wave field cancel^{18}. The same number of photons arrives from both sides and the scattering events are balanced. For the same reason, we do not expect any asymmetric heating of the particle. Radiation pressure and dipole forces are also included in the general Mie calculation (see Methods). They become relevant for larger particles, as seen in Supplementary Fig. S1. Photophoretic forces emerging from the interaction of a heated particle with its gaseous environment are completely negligible. At a residual pressure of P=10^{−8} mbar, a 100nm particle encounters a residual gas particle very rarely, on average every 300 μs. Moreover, a collision with a single N_{2} or O_{2} molecule will not impart any noticeable momentum kick onto the nanoparticle whose mass exceeds that of its collision partner by a factor 10^{8}. We consider it a particular strength of our source design that we can exclude these environmental disturbances with certainty.
Summarizing, we see substantial cavity cooling of pure silicon (Si) nanoparticles in a highvacuum environment. The cavityassisted readout also provides information about the particle’s polarizability, mass and velocity. Our demonstration is an important step towards quantum experiments with high mass particles. Although first new bounds on continuous spontaneous localization^{22,23} will already come into reach with quantum interferometry at a mass range of 10^{5} amu, certain tests will require nanoparticles of 10^{8}–10^{10} amu or more^{24}. Objects that are big are, in principle, still compatible with an interferometer concept that prepares and probes quantum coherence using pulsed optical ionization gratings^{25}, especially when working in the time domain (OTIMA)^{23}. The work function of pure silicon (Si) is well matched to that.
Future explorations of nonlinearities in quantum mechanics^{22,26,27,28,29} will still require transit and coherence times of a few seconds at least. Our successful demonstration of cavity cooling by a factor of 30 in transverse energy is a promising starting point. It is interesting to consider multimode cavity cooling^{30} to reduce the trapping forces close to the cavity centre to increase the cooling rate. Experiments are also on the way to extend the source to internally cold and massselected single particles on demand.
Methods
Launching silicon nanoparticles in a highvacuum environment
Green light from a frequencydoubled Nd:YAG laser (Innolas, 532 nm, 15 mJ, 4 ns) is directed onto the back side of a 500μm thick and chemically cleaned silicon wafer (111 cut), which is attached to a quartz plate and suspended in high vacuum (<1 × 10^{−8} mbar). The origin of this method is similar to that of laserinduced acoustic desorption^{31,32} with the difference that laserinduced acoustic desorption experiments are targeted at releasing surface adsorbents. Here we release nanomaterial from the pristine silicon surface itself by stress. The purity of the material is verified with energydispersive Xray scattering inside an SEM.
The particles are launched by the laser, but not necessarily in the same laser pulse that creates them. We also observe the formation of silicon dust on the front surface, which is then cleaned in subsequent laser shots. The fraction of observed particles that fall into the parameter range suitable for cooling amounts currently to ~1%. The parameter space is spanned by the size, lateral position and velocity of the particles. Most particles are still too big. They average over the standing wave and scatter so much that they may even extinguish the intracavity power. For that reason, they are also detected most easily.
Silicon nanoparticles offer promising properties for cavity cooling as well as for future quantum interference studies alike. They exhibit a very high polarizabilitytomass ratio in comparison with many other dielectrics and are therefore well susceptible to optomechanical forces. Their high refractive index, n(1,560 nm)=3.47(1), is associated with a relative permittivity of ∈=n^{2}=12.04(1). Using the Clausus–Mosotti relation, we can relate the atomic polarizability and bulk permittivity, and find a value of α=4πε_{0}R^{3}(∈−1)/(∈+2). The work function of silicon is W=4.52 eV and indicates that singlephoton ionization can easily be implemented using an ultraviolet or vacuum ultraviolet laser, as required for future OTIMA interference experiments^{23,25}.
Lasercavity stabilization
We use a fibre laser at 1,560 nm. It has a shortterm (50 ms) line width of 20 kHz. Laser and cavity are locked by a slow and a fast feedback loop. Fast feedback is implemented via frequency modulation of the incident laser light in the doublepass AOM 1 (Fig. 1). It operates with unity gain at 150 kHz. A slow active detuning and feedback loop is implemented by a piezoelectric displacement of the flat cavity mirror R1. This loop has a bandwidth of about 10 kHz. We exploit the intrinsic mirror birefringence to generate a dispersive locking signal without the need for actively modulating any optical element^{17}. The highfinesse cavity is not only sensitive to the transiting nanoparticles but also to the tiny thermal expansion caused by the residual absorption in the mirror coating^{33,34}. A rise in the intracavity intensity will lead to an even increased heating of the mirror coating and further thermal expansion. When the laser is reddetuned with respect to the optical cavity, this can result in selfstabilization but also in selfdriven length oscillations with frequencies of the order of a few kilohertz in case of high laser intensities. To avoid these instabilities, the feedback modulation of the laser frequency must be fast enough. This fast feedback suppresses the slow cavity phase shift that is related to the particle’s passage through the Gaussian envelope along x. Only the oscillatory coupling along z remains, which is caused by the particle’s motion across the intracavity standing light wave.
Time evolution of the cavity field
The time evolution of the cavity field amplitude a(t) can be written as
where η is the pump field, Δ is the lasercavity detuning, κ is the cavity loss rate (line width), U_{0} is the cavity shift and f(x) is the cavity mode function, which is explored by the particle moving along x(t). A formal integration of the cavity equation from time t=−∞ yields
In the absence of any particle, the cavity assumes the stationary state a_{0}=η/(κ−iΔ). To lowest order, a slowly moving particle would lead to a quasistationary field amplitude a(t)≈η/(κ−i(Δ+U_{0}f^{2}(x(t)))). The formal solution (equation 2) describes the delayed reaction of the cavity to the moving sphere, which primarily modulates the phase of the field. As the cavity reaction timescale 1/κ is finite, the particleinduced phase shift turns into an intensity modulation only after another delay. This explains the hierarchy of the observed phenomena in the cavity. The scattered light is an immediate signature of the particle position, followed by the delayed phase reaction of the cavity, and its intensity change, which reacts the slowest.
Optical forces on a dielectric particle in a cavity mode
The optical properties of the silicon particle in the presence of a linearly polarized standingwave cavity field E_{0} can be described using Miescattering theory^{35,36}. The internal and scattering field components, E_{int} and E_{sca}, can be expressed in terms of a spherical wave expansion. The lightinduced force acting on the sphere is then computed by integrating the Maxwellian stress tensor that is associated with the modified external field components E_{ext}=E_{0}+E_{sca} and B_{ext} over the sphere surface^{37}. Apart from weak transverse forces due to the Gaussian profile of the cavity field, we find that the force F=F_{z}e_{z} is oriented along the standingwave axis. We may express it in terms of the coupling frequency U_{z} as F_{z}=−ħkU_{z}a^{2}sin(2kz)exp(−2(y^{2}+x^{2})/w^{2}). Supplementary Fig. S1 shows the transverse force for a pointlike particle (green) compared with a full description (blue), which takes the finite particle size into account. For a sphere radius over R=120 nm, the force along the standing wave starts to deviate from the point particle approximation with the effective coupling frequency
At a particle radius of about 190 nm, the force vanishes and it changes its sign for even larger radii. The force F_{z} determines the motion along z^{38},
where we assume that the particle traverses the cavity mode along the x axis. From this, we extract the harmonic frequency f_{trap} for a particle trapped (channelled) at an antinode of the standing wave using , where P_{in} is the incoupled power, and k=2π/λ and c are the speed of light. We measure a frequency of 138 kHz at a normalized scattering S_{N}=0.9 where the oscillation amplitude explores 33% of the trap potential. Taking the anharmonicity^{39} into account, we deduce a harmonic trap frequency f_{trap}=145 kHz. For a silicon point particle maximally coupled to the cavity mode, one expects f_{trap}=183 kHz. The difference is attributed to the nonmaximal coupling of a finitesized particle. We measure U_{z}=2.3(4)κ, which corresponds to the passage of a silicon sphere with a radius of ~150 nm that misses the cavity centre by 0.4 beam waists w_{y} along the y axis.
Velocity of the particle in the optical potential
Because of cavity cooling, the velocity of the particle along z is reduced to a level at which it is influenced by even a small field in the exit wing of the Gaussian cavity beam. The corrugated optical potential modulates the velocity of the particle. At a maximum of the coupling, for instance, it is higher than outside the cavity mode. Assuming a static field amplitude and a constant velocity along x, the moving particle experiences the timedependent force
One can formally integrate the equation of motion to obtain
For a weak potential, this can be approximated to first order by setting z(t)=v_{0}t,
In Supplementary Fig. S2, this expression (red) is plotted for a test particle together with its optical potential (blue). At an antinode/node of the field, the velocity is higher/lower than far out of the cavity mode. It oscillates around its final exit value v_{0}.
The particle velocity at finite coupling will be the same as far beyond the mode as long as the time spent at high and low potential averages out. To determine whether this is the case, we integrate the scattering intensity I_{S}=I_{C}S_{N}(t) V_{opt}(t) between the last two maxima over time, subtract the offset (Supplementary Fig. S3 yellow area, A_{1}) and compare it with the area A_{2} under the Gaussian envelope (area enclosed by the orange lines). If a particle spends more time at low fields, this will result in a smaller area under I_{S}. For the numerical example of Supplementary Fig S2, the ‘measured velocity’ v_{m} at finite field and the ‘true final exit velocity’ v_{f} at zero field will be equal and we find an area ratio of r_{A}≡2A_{1}/A_{2}=1. In the parameter regime w/v_{x}>>λ/2v_{z}, the Gaussian envelope causes only a negligible deviation of r_{A} from 1.
In contrast to that, a particle that is nearly or weakly trapped will spend more time in the low field region than in the high field. This results in r_{A}<1 and the measured velocity v_{m} would underestimate the true final velocity v_{f} by the factor r_{v}≡v_{m}/v_{f}<1. On the other hand, we obtain r_{v}>1 if we overestimate the true velocity in our measurement. By simulating trajectories for different field strengths, we examine the correlation between r_{A} and r_{v} (see Supplementary Fig. S4). We distinguish two cases: particles that are trapped in the optical potential (blue dots) and untrapped particles travelling over the standing wave (red dots). For untrapped particles, the smaller the area ratio r_{A} is, the more we underestimate the true velocity (r_{v}<1). For trapped particles (blue dots), we find r_{v}<1 for r_{A}≲0.9 and r_{v}>1 for 1>r_{A}≳0.9. Both the analytical and the numerical considerations show that the area ratio is a good measure for the validity of our method to extract the final velocity. For the particle studied in the main text (Fig. 3), we obtain a ratio of r_{A}=0.98(0.06), which assures that our measurement does not underestimate the true final exit velocity.
Reconstruction of the particle trajectory
We extract the particle position z(t) from the normalized scattering curve S_{N} in the following manner. First, we divide S_{N} by a fitted Gaussian envelope and then we take the inverse of the sinusoidal part. We assume the local maxima of S_{N} to be positioned exactly at the antinodes of the standing light wave. We distinguish two sorts of local minima: those with a value near zero indicate that the particle passes through a node of the light field; nonzero minima appear at the reversal points, while the particle is channelled along an antinode of the standing wave. At both the maxima and the zerovalued minima, the coupling is insensitive to the particle’s change in position. This leads to discontinuities in the reconstruction of the trajectory, which are corrected with a linear regression. Supplementary Fig. S5 extends Fig. 3e in the main text by showing the full reconstruction from the particle’s entrance up to its exit of the Gaussian beam mode.
Intensity noiseinduced acceleration
Successful cavity cooling requires that the local intensity maximum follows the maximum of the coupling curve in time, ideally with a phase lag of 90°. Only then the particle will climb higher than it falls in the potential well, which is modulated by the particle itself. This is clearly visible in Fig. 3b,c and in Fig. 4b. The complementary intensitycoupling correlation (phase lead of 90°) results in heating. To study this effect, one might consider tuning the laser from below to above the cavity resonance, that is, from Δ=−κ→Δ=+κ. A realization of this idea is, however, prevented by the thermal expansion of the mirror coating, which reduces the cavity length as a function of the intracavity laser intensity, admitting more light to it if the laser is initially bluedetuned. This leads to an instability and thermal runaway.
However, imperfections in the lasercavity stabilization lead to residual fluctuations of the intracavity intensity, which are uncorrelated to the particle dynamics. The intensity noise can therefore lead to temporary heating when the intensity maxima precede the maxima of the coupling curve in time. Figure 5 shows a particle traversing a bluedetuned cavity (adjusted for cooling as in Fig. 3). A comparison of the entrance and exit velocity shows again a net reduction of the transverse kinetic energy (that is, cooling). However, for the limited time span shown in Fig. 5b, the intracavity intensity noise increases the kinetic energy by ~14%. As expected for genuine cavity cooling/heating and as shown in Fig. 5c, this effect coincides with a phase slip (change of of sign) between the maxima of the intracavity intensity and the maxima of the coupling curve. Overall, the transverse kinetic energy of this third particle is reduced by more than a factor of 8.
Additional information
How to cite this article: Asenbaum, P. et al. Cavity cooling of free silicon nanoparticles in high vacuum. Nat. Commun. 4:2743 doi: 10.1038/ncomms3743 (2013).
References
Hänsch, T. W. & Schawlow, A. L. Cooling of gases by laser radiation. Opt. Commun. 13, 68–69 (1975).
Wineland, D. & Dehmelt, H. Proposed 10^{14}δv<v laser fluorescence spectroscopy on Tl^{+} monoion oscillator III (side band cooling). Bull. Am. Phys. Soc. Ser. II 20, 637 (1975).
Dalibard, J. & CohenTannoudji, C. Laser cooling below the doppler limit by polarization gradients: simple theoreticalmodels. J. Opt. Soc. Am. B 6, 2023–2045 (1989).
Aspect, A., Arimondo, E., Kaiser, R., Vansteenkiste, N. & CohenTannoudji, C. Laser cooling below the onephoton recoil energy by velocityselective coherent population trapping. Phys. Rev. Lett. 61, 826–829 (1988).
Kasevich, M. & Chu, S. Laser cooling below a photon recoil with threelevel atoms. Phys. Rev. Lett. 69, 1741–1744 (1992).
Shuman, E. S., Barry, J. F. & DeMille, D. Laser cooling of a diatomic molecule. Nature 467, 820–823 (2010).
Anderson, M. H., Ensher, J. R., Matthews, M. R., Wieman, C. E. & Cornell, E. A. Observation of BoseEinstein condensation in a dilute atomic vapor. Science 269, 198–201 (1995).
Horak, P., Hechenblaikner, G., Gheri, K. M., Stecher, H. & Ritsch, H. Cavityinduced atom cooling in the strong coupling regime. Phys. Rev. Lett. 79, 4974–4977 (1997).
Vuletic, V. & Chu, S. Laser cooling of atoms, ions, or molecules by coherent scattering. Phys. Rev. Lett. 84, 3787–3790 (2000).
Maunz, P. et al. Cavity cooling of a single atom. Nature 428, 50–52 (2004).
Leibrandt, D. R., Labaziewicz, J., Vuletic, V. & Chuang, I. L. Cavity sideband cooling of a single trapped ion. Phys. Rev. Lett. 103, 103001 (2009).
Chan, H. W., Black, A. T. & Vuletic, V. Observation of collectiveemissioninduced cooling of atoms in an optical cavity. Phys. Rev. Lett. 90, 063003 (2003).
Wolke, M., Klinner, J., Kessler, H. & Hemmerich, A. Cavity cooling below the recoil limit. Science 337, 75–78 (2012).
Li, T., Kheifets, S. & Raizen, M. G. Millikelvin cooling of an optically trapped microsphere in vacuum. Nat. Phys. 7, 527–530 (2011).
Kiesel, N. et al. Cavity cooling of an optically levitated submicron particle. Proc. Natl Acad. Sci. USA 110, 14180–14185 (2013).
Gieseler, J., Deutsch, B., Quidant, R. & Novotny, L. Subkelvin parametric feedback cooling of a lasertrapped nanoparticle. Phys. Rev. Lett. 109, 103603 (2012).
Asenbaum, P. & Arndt, M. Cavity stabilization using the weak intrinsic birefringence of dielectric mirrors. Opt. Lett. 36, 3720–3722 (2011).
Nimmrichter, S., Hammerer, K., Asenbaum, P., Ritsch, H. & Arndt, M. Master equation for the motion of a polarizable particle in a multimode cavity. N. J. Phys. 12, 083003 (2010).
Du, Z. R. et al. Enhancement of laserinduced rear surface spallation by pyramid textured structures on silicon wafer solar cells. Opt. Express 20, A984–A990 (2012).
Pflanzer, A. C., RomeroIsart, O. & Cirac, J. I. Masterequation approach to optomechanics with arbitrary dielectrics. Phys. Rev. A 86, 013802 (2012).
Mabuchi, H., Turchette, Q. A., Chapman, M. S. & Kimble, H. J. Realtime detection of individual atoms falling through a highfinesse optical cavity. Opt. Lett. 21, 1393–1395 (1996).
Nimmrichter, S., Hornberger, K., Haslinger, P. & Arndt, M. Testing spontaneous localization theories with matterwave interferometry. Phys. Rev. A 83, 043621 (2011).
Haslinger, P. et al. A universal matterwave interferometer with optical ionization gratings in the time domain. Nat. Phys. 9, 144–148 (2013).
Kaltenbaek, R. et al. Macroscopic quantum resonators (maqro). Exp. Astron. 34, 123–164 (2012).
Reiger, E., Hackermüller, L., Berninger, M. & Arndt, M. Exploration of gold nanoparticle beams for matter wave interferometry. Opt. Commun. 264, 326–332 (2006).
Penrose, R. On gravity’s role in quantum state reduction. Gen. Rel. Grav. 28, 581–600 (1996).
Adler, S. L. & Bassi, A. Is quantum theory exact? Science 325, 275–276 (2009).
Bassi, A., Lochan, K., Satin, S., Singh, T. P. & Ulbricht, H. Models of wavefunction collapse, underlying theories, and experimental tests. Rev. Mod. Phys. 85, 471–527 (2013).
Nimmrichter, S. & Hornberger, K. Macroscopicity of mechanical quantum superposition states. Phys. Rev. Lett. 110, 160403 (2013).
Habraken, S. J. M., Lechner, W. & Zoller, P. Resonances in dissipative optomechanics with nanoparticles: sorting, speed rectification, and transverse cooling. Phys. Rev. A 87, 053808 (2013).
Zinovev, A., Veryovkin, I. & Pellin, M. InMolecular Desorption by LaserDriven Acoustic Waves: Analytical Applications and Physical Mechanisms Ch. 16, 343–368InTech (2011).
Dow, A., Wittrig, A. & Kenttämaa, H. I. Laserinduced acoustic desorption (LIAD) mass spectrometry. Eur. J. Mass Spectrom. 18, 77–92 (2012).
Carmon, T., Yang, L. & Vahala, K. J. Dynamical thermal behavior and thermal selfstability of microcavities. Opt. Express. 12, 4742–4750 (2004).
Dubé, P., Ma, L., Ye, J., Jungner, P. & Hall, J. Thermally induced selflocking of an optical cavity by overtone absorption in acetylene gas. J. Opt. Soc. Am. B 13, 2041–2054 (1996).
Van De Hulst, H. C. Light Scattering by Small Particles Dover (1957).
Bohren, C. E. & Huffman, D. R. Absorption and Scattering of Light by Small Particles Wiley: New York, (1983).
Jackson, J. D. Classical Electrodynamics Wiley: New York, (1999).
Salzburger, T. & Ritsch, H. Collective transverse cavity cooling of a dense molecular beam. New J. Phys. 11, 055025 (2009).
Johannessen, K. An approximate solution to the equation of motion for largeangle oscillations of the simple pendulum with initial velocity. Eur. J. Phys. 31, 511–518 (2010).
Acknowledgements
We are grateful for financial support by the Austrian Science Funds (FWF) in the projects DKCoQuS (W12102) and Wittgenstein (Z149N16), as well as the ESA project number 4000105799/12/NL/Cbi and the EC programme Nanoquestfit (304886). We acknowledge support by S. Puchegger and the faculty centre for nanostructure research at the University of Vienna in imaging the silicon nanoparticles. We are grateful for fruitful discussions with H. Ritsch, C. Genes, W. Lechner, J. Harris, M. Aspelmeyer, P. Schmid and C. Mangler.
Author information
Authors and Affiliations
Contributions
P.A. and S.K. constructed and performed the experiment, performed simulations, data processing and wrote the paper. S.N. performed analytical and numerical calculations in support of the experiment. U.S. participated in the development of the silicon source. M.A. helped in supervision and writing of the paper.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Supplementary Information
Supplementary Figures S1S5 (PDF 730 kb)
Rights and permissions
This work is licensed under a Creative Commons AttributionNonCommercialShareAlike 3.0 Unported License. To view a copy of this license, visit http://creativecommons.org/licenses/byncsa/3.0/
About this article
Cite this article
Asenbaum, P., Kuhn, S., Nimmrichter, S. et al. Cavity cooling of free silicon nanoparticles in high vacuum. Nat Commun 4, 2743 (2013). https://doi.org/10.1038/ncomms3743
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms3743
This article is cited by

Stroboscopic thermallydriven mechanical motion
Scientific Reports (2022)

Quantum rotations of nanoparticles
Nature Reviews Physics (2021)

Uncertaintyinduced instantaneous speed and acceleration of a levitated particle
Scientific Reports (2021)

Strong optomechanical coupling at room temperature by coherent scattering
Nature Communications (2021)

Prospects of reinforcement learning for the simultaneous damping of many mechanical modes
Scientific Reports (2020)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.