Water purification technologies such as microfiltration/ultrafiltration and reverse osmosis utilize porous membranes to remove suspended particles and solutes. These membranes, however, cause many drawbacks such as a high pumping cost and a need for periodic replacement due to fouling. Here we show an alternative membraneless method for separating suspended particles by exposing the colloidal suspension to CO2. Dissolution of CO2 into the suspension creates solute gradients that drive phoretic motion of particles. Due to the large diffusion potential generated by the dissociation of carbonic acid, colloidal particles move either away from or towards the gas–liquid interface depending on their surface charge. Using the directed motion of particles induced by exposure to CO2, we demonstrate a scalable, continuous flow, membraneless particle filtration process that exhibits low energy consumption, three orders of magnitude lower than conventional microfiltration/ultrafiltration processes, and is essentially free from fouling.
With global demand for clean water increasing, there is a continuing need to improve the performance of water treatment processes1,2. Membraneless separation of suspended particles is conventionally achieved by sedimentation, which relies on the gravitational force3. When particle suspensions are stable, for example, due to the particles being small, neutrally buoyant and highly charged, unassisted sedimentation is ineffective and additives are needed to induce aggregation (coagulation or flocculation4) and accelerate sedimentation. Therefore, inducing directed motion of colloidal particles in stable suspensions is critical to membraneless separation processes.
There are several ways to induce directed motion of colloidal particles such as using an external force, for example, electrostatic5, dielectric6, magnetic7, acoustic8, or optical9, inertial effects10 and so on. One less known but significant driving force is a chemical gradient, which causes diffusiophoresis11. Typically, diffusiophoresis is observed in liquid environments where chemical gradients are generated by contact between solutions with different solute concentrations12,13,14,15.
Here we show that diffusiophoresis of colloidal particles can be achieved by dissolution of a gas into a liquid, namely CO2 dissolution into water and its subsequent dissociation that produces ion concentration gradients. Using this principle, we show that the directed motion driven by dissolution of CO2 can be exploited to separate particles with very low energy consumption. Moreover, CO2 is abundant, biologically benign when dissolved in water, and can be easily separated. These features make CO2 dissolution a very promising means to clean water especially for the developing world, which requires water purification technologies that have low energy demands and are not chemically intense2.
where kf and kb are the forward and backward reaction rate constants18, respectively. Reaction (1) implies that transient ion gradients can be created in aqueous particle suspensions when they are exposed to CO2 gas. Most significantly, the generated ions exhibit a large difference in their diffusivities19 (=9.3 × 10−9 m2 s−1 and =1.2 × 10−9 m2 s−1), which may lead to strong particle diffusiophoresis due to a large diffusion potential (≈92 mV for a 100-fold concentration difference, whereas in ordinary salt gradients, the potential is 25 mV for Na+/Cl− and 0.1 mV for K+/Cl−).
To test the hypothesis that exposure to CO2 can induce sufficient ion concentration gradients to drive particle motion, we developed a microfluidic system in which we create a stable gas–liquid interface (Fig. 1a, see Methods section). The microfluidic device, which is made out of ultraviolet-curable epoxy to prevent permeation of gases20, has two main channels bridged by multiple narrow pores that contain a colloidal suspension (Fig. 1b,c).
Upon exposure to CO2 gas (pressure =136 kPa), negatively charged particles (polystyrene, diameter≈0.5 μm, zeta potential≈−70 mV) immediately migrate away from the two gas–liquid interfaces (Fig. 1e,g, Supplementary Movie 1). In contrast (Fig. 1d, Supplementary Movie 2), no appreciable motion of these particles, other than Brownian motion, is observed upon exposure to N2 gas (=136 kPa). Based on our hypothesis, the observed particle migration is mainly induced by the diffusion potential due to H+ and . This assertion is supported by experiments with positively charged particles (amine-functionalized polystyrene, diameter≈1 μm, zeta potential≈60 μm) that migrate toward the gas–liquid interfaces upon exposure to CO2, forming clouds of particles near these interfaces (Fig. 1f,h, Supplementary Movie 3).
The presence of ion concentration gradients, responsible for driving the motion of particles, was confirmed by observing the response of liquid columns filled with pH indicator solution to gas exposure. We used Oregon Green fluorescent dye (0.1 mM) as the pH indicator due to its linear dependence of fluorescence intensity on pH over a broad pH range21. As the water is exposed to CO2 at =136 kPa, the fluorescence intensity immediately decreases near the gas–liquid interfaces, and then the decreasing intensity propagates toward the middle of the column, indicating that pH decreases from the interfaces inward (Fig. 2a). The high intensity evident near the gas–liquid interface is due to the curvature of the meniscus. In contrast to CO2, exposure to N2 at the same pressure does not produce spatial variations in fluorescence intensity, but only a gradual decrease of fluorescence intensity due to photobleaching (Fig. 2b).
Solving coupled diffusion-reaction equations predicts the transient pH distribution under exposure to CO2. The dissolved CO2 and ion concentrations are coupled through the net forward rate of reaction (1) r=kfcc−kb, where cc(x,t) is the concentration of dissolved CO2, and ci(x,t) gives the concentrations of both generated ions, H+ and , which are effectively equal due to local charge neutrality22,23. Then, solving the diffusion-reaction equations ∂cc/∂t=Dc∇2cc−r and ∂ci/∂t=Di∇2ci+r yields the transient ion concentration distribution, where Dc is the diffusivity of CO2 and Di is the ambipolar diffusivity of the ions. The calculated pH distribution (Fig. 2d) shows reasonable agreement with the observed fluorescence intensity profile (Fig. 2c). As the pH decreases from 5.6 (the pH of water in equilibrium with the atmospheric CO2 concentration, =40 kPa) down to 3.8 for =136 kPa, a nearly 100-fold difference in ion concentrations occurs within the column.
This chemical gradient generated by dissolution of CO2 induces particle migration via diffusiophoresis. The particle diffusiophoretic velocity is expressed as up=Γp∇lnci, where the prefactor Γp is the diffusiophoretic mobility, which is a measure of the strength of diffusiophoresis based on surface-solute interactions11. By solving an additional advection–diffusion equation for the particles, we obtain the particle dynamics driven by the dissolution of CO2 (Supplementary Discussion). The one-dimensional transport model captures the key dynamics that are consistent with the experimental observations for both the negatively (Fig. 3a,c) and positively charged particles (Fig. 3b,d), where the negatively charged particles move away from the gas–liquid interface and subsequently focus to the centre of the column; motion is in the opposite direction for positively charged particles. From calculations at other conditions than those of these experiments, we note that the minimum CO2 pressure needed for inducing appreciable particle motion is much lower than 136 kPa, but it must be sufficiently higher than the atmospheric partial pressure of CO2 (see Supplementary Fig. 1, Supplementary Table 2, and Supplementary Discussion).
Membraneless water filtration
The observed colloid dynamics suggest an alternate route to separating particles without the use of membranes or filters, which is by exposing the colloidal suspension to CO2 to concentrate the particles locally as in field-flow fractionation24,25. A continuous flow particle filtration device is illustrated in Fig. 4a. A colloidal suspension flows through a straight channel in a gas permeable material, in this case, polydimethylsiloxane (PDMS)26,27. Separated by a thin wall, a CO2 gas channel passes parallel to the main flow channel. The gas permeates through the wall and dissolves into the flow stream, inducing particle motion transverse to the flow direction; the direction of motion depends on the particles’ surface charge. An air channel on the other side of the wall prevents saturation of CO2 in the suspension, thus sustaining a greater concentration gradient and enabling further migration of particles by diffusiophoresis. After all of the particles have been concentrated at one side of the channel, they are separated by splitting the flow near the outlet.
The removal of colloidal particles using our method is presented in Fig. 4b–e, where the device is made out of standard PDMS. Negatively charged polystyrene particles, which are initially distributed uniformly (Fig. 4b), migrate away from the wall that is adjacent to the CO2 channel as they flow downstream, and are eventually separated from the main stream (Fig. 4c). Positively charged particles can also be filtered using the same principle (Fig. 4d,e). The particle removal rate in terms of log reduction value is estimated to be 5.3 (see Methods and Supplementary Fig. 3), which is comparable to values for conventional microfiltration and ultrafiltration techniques28.
Since the demonstrated method does not involve any filters, its energy consumption is low compared to conventional filtration methods. Energy dissipation is reduced because the fluid may flow through a channel that is much wider than the particles instead of passing through pores that are smaller than the particles. Based on the current channel geometry (width × height × length=0.1 × 0.02 × 30 mm3) and flow rate (2 μl h-1), the pressure drop across the channel is Δp≈0.2 kPa. Assuming 50% recovery of water from the suspension, the energy consumption is estimated as 0.12 mW h l−1, at least three orders of magnitude lower than the energy consumed in typical microfiltration and ultrafiltration processes29,30 (0.1∼20 W h l−1). The energy efficiency can be further enhanced by optimizing the channel geometry such as increasing the channel height to reduce the pressure drop for a given flow speed.
Furthermore, the proposed device is easily scalable due to its simple design, for example by using parallel flow channels (Fig. 4f). Such a design allows easy scaling-up in both the in-plane and out-of-plane directions due to the isotropic permeability of gas in PDMS31. As a proof of concept, a 10-fold upscaled device made out of a monolithic PDMS block is shown in Fig. 4g–j. Likewise, a million-fold upscaling, which is feasible using standard microfabrication techniques, would purify water at ≈50 l per day. The dissolved CO2 in the output streams can be removed by equilibration with air (see for example, ref. 27). The waste stream could pass then through the same process multiple times to further concentrate the particle stream and extract additional water.
By exploiting the dissolution of CO2 as a way to drive particle motion, we have demonstrated a membraneless method that is capable of separating the types of particles that would otherwise form a stable suspension. Due to their small size, surface charge, and the absence of dissolved ions to screen the charge (that is, a large Debye length), the particles we separate would be difficult to remove via sedimentation. The proposed technique is easily scalable and shows a three order of magnitude lower energy consumption than conventional filtration systems, suggesting the technique could be particularly beneficial in both the developing and developed worlds2. We suggest that the proposed technique could be used either to replace microfiltration and ultrafiltration or benefit such conventional filtration processes by mitigating membrane fouling. Also, considering that most bioparticles are charged32, the proposed method can be utilized to remove bacteria and viruses without chlorination or ultraviolet treatment2,30.
Efficient scaling-up of the process to significant flow rates requires optimization of the channel dimensions, the flow rate in each channel, the split ratio, and the number of parallel channels. While frictional losses can be reduced by using a wider or taller channel, increasing the width decreases the magnitude of the concentration gradient. Reduced gradients and lower residence times due to higher flow rates can be compensated by using longer channels at the expense of increasing the required energy input. Longer and narrower channels can also be used to overcome reductions in the diffusiophoretic driving force in applications with sufficient background salt concentrations. To assess the extent of the decrease in the diffusiophoretic driving force with increasing salt concentrations, further experiments with controlled amounts of common salts as well as representative samples with typical mineral contents from industrial and natural water sources would be valuable. Long-term experiments are also needed to assess fouling, such as by proteins or bacterial extracellular polymeric substances.
Our demonstration of particle transport driven by CO2 dissolution is not limited to particle separation, but may also explain the mechanisms underlying some applications that involve dissolution of CO2, such as the stabilization of bubbles via particle assembly at their surfaces33 and the enhancement of froth flotation through the use of CO2 bubbles34. These applications require collection of particles at gas–liquid interfaces, and Fig. 1h demonstrates that even hydrophilic particles can be collected at a gas–liquid interface from a dilute suspension.
Liquid column experiments
The microfluidic device for the liquid column experiments shown in Fig. 1 was made out of ultraviolet-curable epoxy (NOA81, Norland Products) using the microfluidic sticker technique35. The channels were 40 μm thick. Humidified gas is fed through the microfluidic channel, which is initially filled with colloidal suspension. The gas pushes out all the suspension in the main channels, leaving behind columns of colloid in the pores that bridge the two main channels, thus creating a stable gas–liquid interface. This is facilitated by small constrictions at the ends of the pores which serve to break the liquid columns at the right place. Once the suspension is flushed out, the outlet is closed to stop the gas flow, which may otherwise interrupt the particle motion. The gas pressure is monitored and controlled by a pressure regulator (Type-10, Bellofram) equipped with a digital pressure gauge (DPG1000B, Omega). The gas pressure of 136 kPa (5 psi above atmospheric pressure) was chosen to allow flow through the device to an outlet at atmospheric pressure. The colloidal particles (polystyrene, Bangs Laboratories; amine-functionalized polystyrene, Sigma-Aldrich) were prepared by dilution in deionized water (Milli-Q, Millipore) to a volume fraction of 0.01%. pH visualization experiments were conducted in the same manner. The pH indicator was prepared by diluting fluorescent dye (Oregon Green 488, Thermo Fisher Scientific) in deionized water at 0.1 mM. The colloidal particles and the dye were observed with an inverted fluorescence microscope (DMI4000B, Leica). The zeta potentials of the colloidal particles were measured using Zetasizer Nano-ZS (Malvern Instruments).
Water filtration experiments
The microfluidic device for the water filtration experiments shown in Fig. 4 was made out of PDMS (Sylgard 184 Elastomer Kit, Dow Corning) using a conventional soft lithography technique. The monomer and the cross linker were mixed at a weight ratio of 10:1. A syringe pump (PhD Ultra, Harvard Apparatus) was used to flow the colloidal suspensions through the filtration device. For the positively charged particle experiments, in order to prevent adhesion of amine-functionalized polystyrene particles to the channel walls, the PDMS was modified with amine by flowing a 1 vol% aqueous solution of 3-aminopropyltrimethoxysilane (Sigma-Aldrich) through the PDMS channel for 20 min followed by rinsing with deionized water for 10 min prior to experiments36.
Log reduction value measurement
Owing to the low flow rate (2 μl h−1) and high fluorescence intensity of the particles, we are able to count the number of individual particles passing through the filtrate stream (Supplementary Fig. 3). During 5 min, out of ∼2.2 × 107 total particles only 104 pass through the filtrate stream, which corresponds to a log reduction value of 5.3.
The coupled reaction-diffusion equations for the CO2 (Supplementary equation (2)) and ion concentrations (Supplementary equation (8)) together with the advection–diffusion equation (Supplementary equation (9)) for the particle concentration were solved in MATLAB using pdepe. Exploiting symmetry, solutions were computed for x∈[0, L] using a fine grid with refinement at x=0 and x=L to resolve gradients in concentration. The particle trajectories xp(t) were computed by interpolating the pre-computed ion concentration solution and numerically integrating dxp/dt=udp(xp(t), t) for several uniformly spaced initial positions using ode113 also in MATLAB. Additional details are provided in the Supplementary Discussion. The model parameters are listed in Supplementary Table 1.
The data that support the findings of this study are available from the authors upon reasonable request.
How to cite this article: Shin, S. et al. Membraneless water filtration using CO2. Nat. Commun. 8, 15181 doi: 10.1038/ncomms15181 (2017).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
We acknowledge support from Unilever Research. We thank Bhargav Rallabandi and Suin Shim for valuable discussions. O.S. thanks the Natural Sciences and Engineering Research Council of Canada (NSERC) for a postdoctoral fellowship.
Suspension of negative particles exposed to carbon dioxide. Negatively charged polystyrene particles suspended in water migrate away from the gas-liquid interface when the suspension is exposed to carbon dioxide.
Suspension of negative particles exposed to nitrogen. When a suspension of negatively charged polystyrene particles in water is exposed to nitrogen, only Brownian motion of the particles is observed.
Suspension of positive particles exposed to carbon dioxide. Positively charged, aminefunctionalized, polystyrene particles suspended in water accumulate near the gas-liquid interface when the suspension is exposed to carbon dioxide.
About this article
Nature Reviews Chemistry (2017)