Topological insulators are candidates to open up a novel route in spin based electronics. Different to traditional ferromagnetic materials, where the carrier spin-polarization and magnetization are based on the exchange interaction, the spin properties in topological insulators are based on the coupling of spin- and orbit interaction connected to its momentum. Specific ways to control the spin-polarization with light have been demonstrated: the energy momentum landscape of the Dirac cone provides spin-momentum locking of the charge current and its spin. We investigate a spin-related signal present only during the laser excitation studying real and imaginary part of the complex Kerr angle by disentangling spin and lattice contributions. This coherent signal is only present at the time of the pump-pulses’ light field and can be described in terms of a Raman coherence time. The Raman transition involves states at the bottom edge of the conduction band. We demonstrate a coherent femtosecond control of spin-polarization for electronic states at around the Dirac cone.
When exciting materials with femtosecond laser radiation, generally the observed phenomena are manifold. The photon energy is directly transferred to electrons. The sharp electronic energy distribution smears out and the initially coherent excited electronic system thermalizes by scattering processes in the momentum space resulting in decoherence. Since electrons carry a spin, magnetic information is strongly entangled with this coherence – decoherence transition process. The rearrangement of charge in addition causes a movement of the atoms, however with a delay of picoseconds. In ferromagnetic materials, a coherent interaction of the photon field with the spins has been evidenced that triggered research in the new direction of femtomagnetism1,2,3,4. As one mechanism the generation of a photo-induced optical anisotropy in oxides like YMnO3 has been discussed. This effect is related to a distinct localized level scheme and acts as a mechanism to create an ultrashort spin polarization5. Non-equilibrium spin-polarization in semiconductors6 leads to spin-galvanic effects7 and/or spin helical modes due to an interplay of spin coherence and diffusion8. Here, very interesting is the case of topological insulators9,10,11 that combines both: spin-properties, via the spin momentum locking12,13,14,15,16,17,18,19,20,21, and semiconductor properties because of their band gap. In the presence of the laser field further coherent effects emerge, shown by Wang et al.22, which arise from an interaction of the periodic laser field and the electron wave functions of the surface bands leading to laser-field induced gaps with periodicity of ħω in energy, known as Floquet Bloch states. The question investigated in this study is, what happens to a spin-polarization induced by the near infrared laser field and is it possible to generate a polarization induced by the photon field that interacts coherently with the spins in the topological insulator? In the following we disentangle the different processes by femtosecond pump-probe experiments giving access to their dynamics. The different stages manifest from the fingerprint of a magnetic coherent state during the first ten femtoseconds of the laser excitation to coherent atomic motion beyond the picosecond time scale originating from strain pulses, seen as GHz oscillation in the magneto-optical Kerr rotation. Possibly this will allow to manipulate spin polarized carrier dynamics in the topological insulator, and the spin dynamics in the spin-polarized surface states itself on THz frequencies.
To probe the ultrafast dynamics in the topological insulator at the surface within the optical penetration depth, simultaneously to the time-resolved reflectivity, the change in the probe-pulse polarization is determined23. This allows sampling not only the electron and phonon dynamics, but also the transient birefringence induced by the pump-pulse, and eventual rearrangements of the spin polarization induced in the first femtoseconds to nanoseconds after laser excitation24,25. If a transient spin-imbalance is present in the all-optical pump-probe experiment, the probe pulse’s polarization change related to a complex Kerr angle can be detected. In our experiments the pulse has a full width of 40–80 fs and a wavelenght of λ = 800 nm corresponding to 1.55 eV photon energy. The complex polarization angle (rotation of the polarization axis and ellipticity) is extracted using an optical-modulation technique (see methods). All experiments have been conducted at 295 K, the Kerr angles are in the order of a few 1/100 degree and comparable to ultrafast demagnetization experiments.
In Fig. 1 we present the phonon modes indicating the typical phonon resonance as a proof of the high quality of the Bi2Te3 thin film layered samples surface. The movement of the atoms is traced by the delayed femtosecond probe in the reflectivity evolution after pump-pulse excitation. This phonon mode at 1.84 THz represents a 540 fs dynamics of the atoms moving in the A1g mode, which is the most prominent mode26,27. On a longer time scale a slower oscillation is evident. It originates from the thermal expansion within the surface after energy deposition, triggering a breathing of the Bi2Te3 layer. This phonon frequency is determined by the thickness and the velocity of sound ~4 nm/ps (4000 m/s) and we extract a breathing of the standing wave of 63 GHz for the longitudinal phonon mode.
An ultrafast access to the pump-pulse induced change of birefringence is given by the complex polarization rotation presented in Fig. 2. It is governed by the dielectric tensor ε, which (in the polar configuration) has a particularly easy form with a diagonal non-magnetic part and an off-diagonal part that is related to a complex polarization angle and present on different time scales28. In ferromagnetic materials the magneto-optical Kerr angle is proportional to the materials magnetization. Moreover, it is known that the normalization of the spin-sensitive off-diagonal optical contribution with the non-magnetic diagonal optical contribution can cause a non-magnetic modification of the magneto-optical properties, by the modification of the optical reflectivity alone. A direct comparison of the transient Kerr signal with the time-resolved reflectivity gives a first hint whether the signal constitutes the pure magnetic signal or the diagonal elements of the dielectric tensor cross talk with the complex Kerr angle, as the crystal is rotated29 or as a function of delay time30. In non magnetic materials different effects can contribute to a change in the complex polarization rotation which is sensitive to off-diagonal terms of the dielectric tensor. We present the pump-pulse induced changes in the complex polarization angle of the probe pulse as a function of the delay time in Fig. 2b for different orientation of the crystal with respect to the plane of incidence of the laser light. Interestingly one observes a 30-ps slow oscillation period, corresponding to a 31 GHz mode, decaying with a rate of 100 ps. This oscillation’s amplitude mirrors the crystal symmetry of the film while rotating the crystal: the film growth on the substrate is defined by the underlying symmetry. Two domains are known to be present resulting from a van der Waals growth mode of the the topological insulator epilayer, rotated by 180° to each other31,21. This converts the hexagonal symmetry of the crystal that nominally would give rise to a three-fold symmetry with period of 120°, to a two-fold symmetry with 180° period seen in Fig. 2d. Furthermore it can be noted that the Kerr rotation is not sensitive to the phonon modes at 63 GHz, since those are not present in the Kerr signal. Experiments at different magnetic fields and reversing the handedness of the circular polarization of the pump beam do not provide evidence for spin-packets propagating at the sample surface, as in the case of the laser induced spin helix in a GaAs/AlGaAs quantum well for example8. Such a signal should reverse the spin orientation of the pump-pulse induced spin polarization. This 31 GHz mode is not present in the dynamics of the reflectivity where we find the longitudinal standing wave. A coupling of the off-diagonal optical elements of the optical tensor to a different breathing mode of alternative symmetry cannot be excluded as a probable origin here.
A dependence on the pump-pulse polarization is seen in the presence of the pump-pulse’s laser field on ultrashort time scales. It can be separated as shown in Fig. 2a, inset. The Kerr rotation for right circularly and left circularly polarized pump pulse reveals a characteristic negative or positive peak, while the linear pump-pulse excitation shows an intermediate slope. The latter contribution is related to the heat and stress induced effects, as observed for longer delay times, and suggests discussing the difference signal in the following. We notice that this ultrafast signal remembers the light-field polarization. It seems related to a pump-pulse induced ultrashort time polarization in the material, evident in a sign change of the signal. Due to its fast decay within excitation pulses’s duration, it seems to be coherent within the excitation pulse at first glance. Such an ultrafast polarization induced signal in the refraction has been observed by Gedik et al. and ascribed to an ultrafast induced spin polarization followed by a very fast depolarization15. By studying Kerr rotation and ellipticity simultaneously, we will see in the following that this ad hoc explanation of the shape of the signal maybe not correct.
To determine its properties we conducted a composition dependent experimental series shifting the Fermi energy though the gap of the topological insulator (Bi1−xSbx)2Te3 alloy film with varied Sb content (39, 43 and 45%). The variation goes from n-doped via intrinsic to p-doped. For Sb = 43% a minimum carrier density is extracted from Hall effect measurements of n ~ 1017 cm−3 (in the following compensated sample). The surface band Dirac cone was characterized by angle-resolved photoemission spectroscopy (ARPES) experiments and band structure calculations32,33. To extract a spin-signal related to a pump-pulse induced spin-asymmetries, we use the pump right circular, left circular Kerr rotation and ellipticity as a difference signal to the linear pump-pulse polarization. The linear pump-pulse induced changes are assumed to be spin-polarization independent. It appears that both signals, presented in Fig. 3, have a characteristic slope: the shape of the signal is a combination of a Gaussian or Gaussian-derivative like signal. Moreover the ellipticity has a significant delay as compared to the Kerr rotation, which amounts to about 80 fs. The sign change of the Kerr rotation is observed as small hump at a positive delay, e.g. later arrival of the probe-beam pulse relative to the pump-beam’s center. The opposite holds for the Kerr ellipticity where it appears at negative delay, e.g. earlier arrival of the probe-beam pulse relative to the pump-beam’s center and points to a phase shift in-between the signals. To extract the time scales of the dynamics and its components we employ a model applied originally to GaAs6 and adapted for photo-induced circular optical anisotropy in oxide insulators5. There it describes the dipole transition above the band gap, from hybrid 2p–3d ground states into Mn3+ 3d states. Within a characteristic time (Raman coherence time τR) a transition in between a degenerate state with symmetry to changing magnetic quantum number and thus the magnetic polarization in the transient state is its basic idea. This allows describing the typical shape of the polarization observed for the complex Kerr rotation (ϕK = θ + iε) around a resonance
with t as temporal evolution (pump-probe delay) and , the pulse width, is given by τFWHM full width at half maximum (FWHM). The Raman coherence time τR and the complex amplitudes are related to the dielectric susceptibility tensor in analogy to ref. .
It is noted that the pump-induced anisotropy is quite large compared to the amplitudes of the signal at longer time scales. The Kerr rotation and ellipticity induced by the pump-pulse for oblique incidence of 45° from the normal were fitted simultaneously. The signal is asymmetric, and as a consequence we extract a Raman coherence time that is shorter than the laser-pulse width. We find almost constant values around 9–15 fs practically independent of the Fermi level position, with a tendency for a minimum at Sb = 43%. The amplitude factors, related to time-dependent dielectric tensor elements, are responsible for the phase factor. One can see the effect of the different amplitudes given in Fig. 4a, where the ellipticity iε in the complex Kerr rotation follows almost a Gaussian shape, and we generate an almost derivative shape for the real part θ. This demonstrates that a coherent polarization effect determines the shape of the spectra in presence of the femtosecond laser field. The phenomenological three level model can be used to derive the different shape observed for Kerr rotation and Kerr ellipticity, where both the real and imaginary part are related via the Kramers-Kronig relation. The analysis is shown in Fig. 3 overlaid to the experimental data and describes the spectra in detail. In Fig. 4a the comparison between real part and imaginary part is displayed for the case of the compensated sample (right polarized pump pulse) and in Fig. 4d the complex Kerr signal is compared for right and left circularly excitation showing the opposite direction of the phase-trace in the complex plane.
To relate these transitions to the band structure of Bi2Te3 (or Sb2Te3) we use ab initio density functional theory band structure calculations and solve the full Dirac equation; the electron-electron interaction is treated in local-density approximation. The bulk-band structure of Bi2Te3 (or Sb2Te3) at around the Fermi level is dominated by the bonding p-orbitals of the Te and the anti-bonding states of Bi. We calculated the j resolved band structure in the simplified model for j = 1/2 and j = 3/2 contributions. For the laser frequency ω with ħω = 1.55 eV we find a resonance for dipole transitions for σ− from mj = 3/2 to mj = 1/2 (σ+ from mj = −3/2 to mj = −1/2) at the Γ point into the lowest unoccupied states above the energy. Relatively flat bands at around the Γ point result in a reasonably large localized density of states for these transitions to form a resonance, corresponding to a transition from Te to the anti-bonding of Bi verified by band structure calculations (see Supplementary Materials). This polarization effect induced change in the Kerr rotation appears only in presence of the pump-pulse. After that the coherence is lost, originating from intra- and interband scattering and dephasing. Thus, this probe of the femtosecond phase space filling is a sensitive probe of the time dependent redistribution of carriers excited at the band edge close to the Γ point and is sensitive to the electronic structure at the Dirac cone here modified by the different composition of the (Bi1−xSbx)2Te3 alloy.
By relating these transitions to the element projected band structure (see Supplementary Materials), we can interpret them as rectification and shift currents34,35. While the first one results in a diffusive current with different velocities of the spin-polarized excited carriers, the other results in a replacement of charge (spin polarized) in the unit cell and a short polarization. In the simplified level scheme of Bi2Te3 this corresponds to a transfer of electrons from the bonding p-orbital of Te to the anti-bonding p-orbital of Bi. Indications for this local shift currents that are hence polarization dependent are seen also in THz emission and pulsed AC photo-voltage generation in Hall bar devices and such current burst can be related to a spin polarized charge current36. In contrast, the Kerr angle allows accessing the pump-induced coherent spin-polarization in the transient state directly. It is interesting to relate our results to the spin- and electron dynamics determined by time-resolved and angle-resolved spectroscopy at the same transition by Cacho et al.37. They report a second spin polarized surface state in the conduction band. From their data and experiments they conclude well separated spin dynamics in these excited states as well as the presence of a significant spin polarization, however the effects they observe appear on a much longer time scales of 1–6 ps. They identify this second spot to contribute with a major role to the spin dynamics of the excited system. The importance of a second Dirac cone for the transitions at around 1.55 eV via a direct optical coupling to this unoccupied Dirac surface state had been pointed out for Bi2Se338, but the role and appearance of this transition in the Bi2Te3 (and (Bi,Sb)2Te3) system is still under investigation.
In conclusion, we discussed dynamic effects induced by the pump pulse at 1.55 eV femtosecond laser excitation detected in the reflectivity dynamics and complex Kerr signal on time scales of femtoseconds to nanoseconds. Coherent phonon modes have been observed, as the A1g mode and modes in the GHz range related to acoustic standing waves of the film. Modes in this frequency range have been observed in the Kerr rotation, e.g. the dynamic signal related to the magnetic properties, however we can exclude a direct, simple crosstalk of optics from the comparison of both modes that have different origin and interaction may be more complex. By subtraction of the linear-pump pulse dynamics from left- and right circular pump-pulse polarization, we find a spin-related signal present only during the laser excitation with different phase for real and imaginary part of the complex Kerr angle. This signal is only present due to polarization of the topological insulator in the presence of the pump-pulses’ light field. We describe the shape of these signals with a pump-induced polarization of the states excited across the band gap of the topological insulator, involving the lower bottom edge of the conduction band that can be analyzed in terms of a Raman coherence time. The states close to the band edge are known to be hybridized with the surface bands, and moreover the optical transitions could be close to the appearance of the second unoccupied Dirac cone inside the conduction band38, so it will be interesting to relate these pump induced polarization effect as a probe of the properties of the topological states in the band gap in future studies. We find a weak dependence for the Raman times with the tendency of a shorter coherence time for the intrinsic films with intermediate Sb composition.
Ultrafast laser spectroscopy
In the all-optical pump probe experiment the magneto-optical Kerr rotation of the probe beam is measured. The pulse has a full width at half maximum of τ = 40–80 fs and a central wave length of λ = 800 nm (Ti:Sapphire amplifier system RegA 9040, Coherent) corresponding to 1.55 eV photon energy. The repetition rate of the laser system used is 250 kHz. The Kerr angle is extracted by means of a photoelastic modulator. All measurements have been conducted at room temperature (295 K). To extract a spin-signal related to a pump pulse induced spin-asymmetries at ultrafast time scales, we use the Kerr signal for linear pump-pulse polarization as a non-magnetic reference. Since the linear pump-pulse induces only transitions equally for spin-up and spin-down electrons, these changes will be spin-independent. The signals for pump right circular, left circular, Kerr rotation and ellipticity are plotted as a difference signal pump-left, right circular minus pump-pulse linearly polarized (see inset Fig. 2a). This allows separating the contributions from electron and phonon dynamics and pump-induced spin-polarization. Interference of scattered light of pump-pulse and probe-pulse at the detector caused by stray light from the pump region, for example by a locally rough spot or periodic modulation of the index of refraction (light induced optical grating), have been identified in the experiments and minimized. This effect known as optical artifact at around τ = 0 is causing a fast oscillation of the signal sampled at each delay. The analysis using the three level model was tested against rigidity of the interdependence of the two variables defining the interval in Table 1 reflect the spread using fixed and variable length of the excitation pulse respectively.
The first set of samples, Bi2Te3 and (Bi,Sb)2Te3 films from the Forschungszentrum Jülich were grown by molecular beam epitaxy (MBE) on Si(111) wafers. Prior to the deposition, the Si substrates were chemically cleaned by the HF-last RCA procedure to remove the native oxide and passivate the surface with hydrogen. The substrates were subsequently heated in-situ to 600 °C for 20 min to desorb the hydrogen atoms from the surface. The Sb, Bi and Te material fluxes were generated by effusion cells with temperatures of 460 °C–470 °C (Bi), 370 °C–390 °C (Te), and 400 °C–420 °C (Sb). For all samples, the Te shutter was opened 2 seconds before the Sb and/or Bi shutter, in order to saturate the Si substrate surface with Te. Throughout the growth, the substrate temperature was set at 300 °C. A low growth rate of ~5–10 nm/h was chosen in order to obtain a smooth and uniform sample surface. In case of the ternary (Bi,Sb)2Te3 samples, the Sb concentrations were determined by Raman measurements and x-ray photoelectron spectroscopy. From high-resolution transmission electron microscopy experiments it is seen that the topological insulator films are fully relaxed from the very first quintuple layer. These layers grow in the so called van der Waals growth mode where only a weak van der Waals force between substrate and the topological insulator epilayer is present. This growth mode results in two domains rotated by 180°31. For these films angle-resolved photoemission spectroscopy (ARPES) revealed the topologically protected surface states combined with band structure calculations for Bi2Te3 and Sb2Te3 films32,33.
The growth of Bi2Se3 layers at the Massachusetts Institute of Technology, second set of films studied, was carried out by molecular beam epitaxy (MBE) under an ultra-high vacuum (UHV) environment (10−9–10−10 Torr). High purity (5N) elemental Bi and Se were co-evaporated from different Knudsen-cells with typical growth rates between 0.5–1 nm/min. (0001)-oriented, epi-ready, commercial Al2O3 (sapphire) wafers were used as a substrate. To improve the surface quality common wet cleaning techniques were employed, followed by in-situ oxygen plasma cleaning to remove organic contaminants from the substrate, finally annealing for an hour at 600 °C, and at 800 °C for 30 min under 10−9 Torr. Substrate preparation as well as the growth process were monitored by in-situ reflection high-energy electron diffraction (RHEED) and indicates atomically flat surface. The temperature of the substrate was kept at 280 ± 5 °C for crystalline Bi2Se3 growth, i.e. in the epitaxial growth regime with a hexagon-on-hexagon orientation and the RHEED pattern of the grown layer is shown in the inset as well. In order to obtain detailed information about the crystal quality of the films, x-ray diffraction (XRD) patterns were studied. 20 QL Bi2Se3 show highly resolvable Laue oscillations around the Bragg peaks, a clear indication of the film’s structural coherence along the growth direction.
Band structure calculations
The ab initio results are obtained with a full-relativistic Korringa-Kohn-Rostoker Green’s function method in atomic-sphere approximation39. We use the LDA functional by Vosko, Wilk, and Nusair40. To identify the character of the states we calculate a k-resolved density (Block spectral density) along the symmetry lines which is additionally resolved by the total angular momentum quantum number j.
How to cite this article: Boschini, F. et al. Coherent ultrafast spin-dynamics probed in three dimensional topological insulators. Sci. Rep. 5, 15304; doi: 10.1038/srep15304 (2015).
T.K., C.H., G.M., J.K., D.G. and M.Mü. thank the Deutsche Forschungsgemeinschaft (DFG) for funding within project “Investigation of directional THz spin currents in topological surface states”, Schwerpunktprogramm 1666 “Topological Insulators: Materials – Fundamental Properties – Devices”. G.M., J.K. and D.G. also thank the Virtual Institute of Topological Insulator (VITI) for financial support. F. K., and J. S. M. would like to thank support by NSF (DMR-1207469), ONR (N00014-13-1-0301), by the MIT MRSEC through the MRSEC Program of the National Science Foundation under award number DMR-0819762, the STC Center for Integrated Quantum Materials under NSF grant DMR-1231319.
About this article
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/