Localized states trap waves propagating in a disordered potential and play a crucial role in Anderson localization, which is the absence of diffusion due to disorder. Some localized states are barely coupled with neighbours because of differences in wavelength or small spatial overlap, thus preventing energy leakage to the surroundings. This is the same degree of isolation found in the homogeneous core of a single-mode optical fibre. Here we show that localized states of a disordered optical fibre are single mode: the transmission channels possess a high degree of resilience to perturbation and invariance with respect to the launch conditions. Our experimental approach allows identification and characterization of the single-mode transmission channels in a disordered matrix, demonstrating low losses and densely packed single modes. These disordered and wavelength-sensitive channels may be exploited to de-multiplex different colours at different locations.
The ability to confine waves is of paramount importance in laser physics1, matter waves2 and optics communications3, while it is fundamental in many technological applications such as optical tweezers4, acoustics5 or quantum optics6. ‘Single-mode’ confinement is a peculiar form of wave storage, in which a single solution of the wave equation is trapped in a system producing a coherent wavefront, which is not subjected to variations originated by interference with other modes7,8,9.
In the case of multimode fibres, light is launched into many modes at once, resulting in a fluctuating intensity profile and in output strongly dependent on the launch conditions and influenced by bending and stretching of the core. This is due to the interference between the modes. Single-mode fibres are today fundamental in communication technologies, allowing extremely high bandwidth data communication immune to intermode dispersion10,11. Single-mode operation instead is obtained by properly shaping a symmetric fibre core7 or with more sophisticated physical effects8,9 so that a single-mode fibre with 5–10 μm core12 provides a single oscillating solution. In such a regime, the intensity profile has a fixed shape along propagation and is independent of the launch conditions: the input-coupling conditions only influence the amount of light coupled to the channel. Absence of defects is important for the realization of high-quality single-mode fibres: any unwanted scattering results in leakage or high-order-mode contributions.
On the other hand, disordered systems may provide a form of confinement, which is know as Anderson Localization13,14. Anderson Localization, a phenomenon still presenting some unexplored aspects15, is known to produce a drastic reduction of the diffusion coefficient16. In his seminal paper, Anderson has shown14 that in a strongly disordered system the available modes are localized states13: a wave in such a system cannot propagate freely but has to jump from a localized state to another, resulting in a nearly zero diffusion coefficient. Localized states are both spatially separated and energetically distant (they are isolated17,18), so that energy has a small probability to be transferred from one state to a neighbour. In other words, if the disorder is strong enough, it may in principle support single-mode states in the form of individual solutions of the wave equation, which do not exchange energy with other degrees of freedom.
Here we report the observation of single-mode states in the regime of Transverse Anderson Localization (TAL) in a disordered optical fibre. TAL is a peculiar form of localization requiring that the refractive index distribution in the transversal plane to the propagation direction must be disordered and the system must be homogeneous along the propagation direction. These two conditions have been experimentally tested for electromagnetic waves in photonic lattices19 and in optical fibres20,21,22, demonstrating that TAL is able to compensate for the natural diffraction of light producing a constant transversal profile size. We exploited disordered binary fibres (DBF)20, realized by melding micron-sized strands of polymethylmethacrylate (refractive index n=1.49) and polystyrene (n=1.59), so that the final product is a disordered structure in the x, y plane, which is invariant along propagation direction z (refs 23, 24). A complete characterization of the disordered fibres is discussed elsewhere25,26,27,28. The transmission channels sustained by these disordered and longitudinally invariant systems are quite robust23, and demonstrated with several configurations and materials19,21. These systems behave as a coherent fibre bundle: light injected at a certain location exits at the corresponding location at opposite facet29 and it is possible to exploit simultaneously several transmission channels at different wavelengths in the same fibre30 (see also Supplementary Note 1).
Locating transmission channels
To locate the transmission channels of a DBF (experimental set-up is shown in Fig. 1, a fibre scheme and image of the tip are shown in Fig. 1c,d), we measured the total transmission as a function of the input position (see Methods). The result is reported in Fig. 2a for a 20-cm-long disordered fibre. T(r) (R is the output coordinate and r the input coordinate, see Methods section) is strongly position-dependent ranging from 10−3 to nearly unity (the distribution reported in Fig. 2f as blue triangles); moreover, the high transmission areas appear to be organized in a set of sparse and highly transmitting channels embedded in a scarcely transmitting sea. A single scan is visualized in Supplementary Movie 1 for a DBF, while in Supplementary Movie 2 we report the same measure for a standard homogeneous multimode fibre. Polarization properties of the modes are investigated in the Supplementary Note 2. The first clue on the single-mode nature of these channels comes from the pattern of the transmitted intensity I(R, r), which is not affected by a small displacement of the input: if Δr is small and r is the location of the localized mode. The two profiles obtained for the input in correspondence of the maximum transmittance (yellow dot in Fig. 2a labelled as bi) and for an input slightly shifted (green dot in Fig. 2a labelled as ci) are nearly indistinguishable. On the other hand, the intensity profile obtained for a barely transmitting input area provides a strongly varying output pattern if the input location is slightly displaced (see Fig. 2d,e where speckles obtained for inputs at di and ei are shown).
In other words, in the neighbourhood of a highly transmitting channel, the shape of the output intensity remains almost unperturbed, exactly like in a single-mode fibre where the shape of the transmitted wavefront is independent on the launch conditions. We now proceed to directly quantify the degree of invariance of the light profile transmitted by a transmission channel. To establish the degree of similitude of two intensity distributions obtained for two different inputs r1 and r2, we will exploit the observable Q(r1, r2) (see Methods) to build Q-maps.
We are interested in finding regions in which the shape of the output pattern does not depend on the launch conditions that is where Q(r1, r2)≅1: the invariance of the output profile is a signature of the single-mode transmission. We expect that the single-mode transmission channels are found in correspondence of a transmittance maxima (for example, (bi) with the profile shown in Fig. 2b); therefore, we computed Q(rbi, r2) for all inputs r2=[x2, y2]. The result is shown in Fig. 3a. The white area represents the inputs r2 for which Q(rbi, r2)≅1, that is where the output patterns are very similar. This result indicates that if light is injected close to rbi the output profile and shape do not vary, that is, that the mode at rbi is unaffected by the launch conditions.
The same procedure has been repeated for the mode at rgi for which we retrieve the Q(rgi, r2) profile reported in Fig. 3b, showing that gi is immune to the launch conditions close to rgi. As a comparison in panel Fig. 3c we report Q(rdi, r2), with rdi corresponding to a poorly transmitting input that is sensible to the launch conditions. To quantify the degree of isolation of a mode, we introduce the ‘dwelling area’ (DA) of a mode (the area of the input that allows to couple all injected light to the same mode), as the area for which Q>0.9. Mode bi results in a DA=8 μm2, mode gi has DA=1 μm2, while for di DA=0.04 μm2. By scanning 20 different regions of 100 μm2 we found an average of 6.5 single modes with DA>0.5 μm2. This means that a DBF, which is 250 × 250 μm2, is able to host ∼4,000 single modes.
Another requirement for single-mode transmission is the resilience to fibre bending. If transmission is carried out by a single-mode channel, interference is absent so that the transmitted intensity profile is not affected by the fibre folding. To check this feature, we exploited an actuator capable of displacing a 20 cm fibre by 1 cm (Sample Mover (SM) in Fig. 1) from a starting configuration (configuration A) to a second one (configuration B). Then, we compared the output intensity profile in the two configurations and computed for all inputs r=[x, y]. reports the degree of similitude of intensity patterns with the same input but in two different fibre configurations. If is close to 1, the fibre displacement is not affecting the light coupled to the fibre at that position, so that is a measure of the modes’ resilience to fibre bending. The result is reported in Fig. 3d, where the clear areas ( close to 1) are due to the presence of bending-resistant transmitting channels, while darker areas correspond to the absence of a single mode at the input location wavelength. In that case, light undergoes diffusion before being coupled to a guided mode or is expelled by lateral leakage yielding an attenuated output, which is strongly dependent on the input (see Supplementary Note 3).
By comparing with T(r) in Fig. 2a, we notice that the higher the fibre transmittance, the higher the resilience to fibre bending: thus, the resilience and the transmittance are correlated. This is proved in Fig. 2f where we report the distribution of transmittances retrieved from the scan reported in Fig. 2a with full triangles, while the transmittances for the locations with (high resilience to fibre bending) are reported by open squares. The average transmittance is 0.04 (visualized by a blue vertical line in the graph), while the average transmittance for the resilient areas is 0.13 (visualized by a red vertical line in the graph).
In sum, it is possible to inject light in a disordered fibre in order to feed modes with intensity profiles that are independent on the launch conditions and resilient to fibre bending; moreover, these modes are located at the transmission maxima and provide a higher transmittance with respect to the average. Now we want to prove that all these characteristics are independent on the particular realization of disorder, and may be found for any disorder realization. In Fig. 4a we report (blue squares) and (red circles) obtained by averaging five different disorder realizations obtained from these different fibres (lengths L=4, 10 and 20 cm) for a total of 15 disorder realizations analysed. The transmittance decreases exponentially as , where C0 is a parameter for the coupling efficiency and is the length over which the transmittance decays of a factor e (leakage length). By fitting the data, it is possible to find the average leakage length cm and the leakage length for the single-mode locations, which is much higher cm. Results presented in Fig. 4a) are retrieved from 15 different measurements confirming the generality of our result.
Now we report on the response of the system at different wavelengths. At difference with standard single-mode optical fibres, which are usually broadband, disorder hosts modes with a narrow linewidth31 and this property has been recently exploited for applications32,33. In addition, disordered single modes are sharp, possessing a subnanometric linewidth34, so that the transmittance of the system strongly depends on the wavelength. In Fig. 4b,c the transmittance maps are obtained at 674 and 532 nm. The locations of the transmittance maxima are different, and the output intensity profiles change. We fixed the input at the location (indicated the transmittance maps (Fig. 4b,c), with a star marker) and reported the two intensity outputs in Fig. 4d,e. The two profiles are nonoverlapping so that if light is injected at rstar the two colours are de-multiplexed.
In summary, modes in a strongly disordered system show a negligible crosstalk accompanied by a inherent resilience to fibre bending and an invariance with respect to the launch conditions. These single modes show a higher transmittance with respect to the locations in which single modes are absent. We also exploited the narrow linewidth of these modes to obtain separation of different colours at different localized output inside the DBF.
To locate highly transmitting channels, we exploited a high numerical aperture (NA) objective (EDMUND #59–880 long working distance objective, NA 0.8) to focus light at the fibre’s input (see Fig. 1e) and a precision piezo stage, which allows to slightly move (piezo scanning range 20 × 20 μm2) the fibre input in order to scan different input locations. Therefore, the intensity I at the fibre output at coordinates [X, Y]=R depends on the input illumination position [x, y]=r: I(R, r). The total transmittance as a function of the input position is T(r)=∑R I(R, r)/Iin, where Iin is the total injected intensity as measured by CCD1.
where represents the intensity I(r, R) normalized in such a way that Q(r, r)=1. Q represents the degree of similarity of the intensity profiles at the output for the inputs at r1 and r2: it is close to 1 if the output patterns are identical, it is close to zero if light intensity is located in two nonoverlapping regions, while it is close to 0.5 for extended random speckle patterns.
The data that support the findings of this study are available from the corresponding author upon request.
How to cite this article: Ruocco, G. et al. Disorder-induced single-mode transmission. Nat. Commun. 8, 14571 doi: 10.1038/ncomms14571 (2017).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
M.L. acknowledges ‘Fondazione CON IL SUD’, Grant ‘Brains2south’, Project ‘Localitis’.
Image of the radiation from the output tip of a DBF (left panel) while the input (input position indicated by a square in the right panel) is scanned.
Image of the radiation from the output tip of an homogeneous fibre (left panel) while the input (input position indicated by a square in the right panel) is scanned.
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/