Introduction

Among the various environmental stimuli, heat is an important parameter to record and amplify. The temperature sensor/detector can be in direct physical contact or in proximate to the object of interest. The latter case is specific to the field of photonics since heat propagates to the sensor through infrared radiation that changes the temperature of the sensor. Thermal infrared sensors/detectors and infrared cameras find many applications in medical, industrial, military and consumer products1. Precision medical thermal imaging of human skin2 can provide clinically relevant information about pathological conditions that affect how the body regulates temperature, or track a healing process around a scar. Electronic skin (or e-skin3) comprises a network of flexible sensors that can conformably wrap irregular surfaces and spatially map and quantify various stimuli4, which is either used on the human body for medical applications or on machine’s body for robotics. Temperature sensors can be bolometer/thermistors5,6, diodes5, thermoelectric/thermopiles7 or pyroelectric sensors8.

Thermopiles and pyroelectric detectors do not require an electrical input signals (unlike bolometers), but rather develop a large voltage under infrared light illumination. A pyroelectric detector functions similar to a capacitor with the pyroelectric material as the dielectric9. The advantage of using a pyroelectric material is the large voltage produced per amount of incident infrared light (104 V/W)10; which makes such devices very sensitive even at room temperature. Pyroelectric detectors have, however, two major disadvantages that limit their commercial applications to detection (for example, burglar alarms) rather than thermometry and thermography. First, under constant exposure, the voltage signal declines with time making it difficult to obtain accurate static temperature measurement without additional expensive mechanical and electronic devices11. Second, it is sensitive to vibration since pyroelectric materials also are piezoelectric.

Thermoelectric materials are attractive for temperature/heat flow sensing applications. In thermoelectric effect, charge carriers thermo-diffuse in a material under a temperature difference. This produces a voltage V=SΔT proportional to the temperature difference multiplied by the Seebeck coefficient S of the material. The Seebeck coefficient of electronic materials used in thermopiles is typically of the order of a few 100 μV K−1 (ref. 7). Nowadays with microtechnology, thermocouples can be replicated and coupled in series to enhance the sensitivity and reach 100 V/W12. The advantage of thermoelectric detection is that the voltage signal is constant versus time under constant illumination; which makes it appropriate for temperature measurement. The drawback is the low Seebeck coefficient of the electronic materials that limits their sensitivity compared with pyroelectric detectors. Recently, inspired by nature13,14, there has been a renew interest in the thermoelectric properties of electrolytes. When an electrolyte is in fact subjected to a temperature gradient, it undergoes molecular reorganization with formation of an ionic concentration gradient via thermo-diffusion (that is, Soret effect). This results in a large ionic Seebeck coefficient as high as several mV K−1, as recently reported for some organic electrolytes15. Polymeric electrolyte based on NaOH-treated polyethyleneoxide have also been shown to reach ionic Seebeck coefficients as large as 11 mV K−1, allowing for charging ionic thermoelectric supercapacitors (ITESCs) by the ionic thermoelectric effect16.

Potentiometric signals from sensors can be amplified by organic transistors. These are used in fact as smart sensors with the common strategy to shift the potential of the gate through the interaction with an analyte or by external stimuli17,18,19. One of the primary methods to improve sensitivity and selectivity of the transistor-based sensors for probing small changes in the gate bias is to develop devices that operate at low voltages and with high transconductance20. In this respect, electrolyte-gated transistors offer unique properties such as low-voltage operation (<1 V) even for thick electrolyte layers21, which is useful in low-power electronics22, biosensors23 and smart textile24,25.

Here we develop an external heat-gated organic transistor, which consists of an electrolyte-gated transistor and an ITESC. When the ionic thermoelectric leg is subjected to a temperature gradient ΔT, it generates a large Soret-induced open voltage that gates the transistor. Hence, this ionic thermoelectric-gated transistor converts a modulation in ΔT to a modulation in the drain current ΔI. Since the operating voltage of our electrolyte-gated transistors is of the same order of magnitude as the variation of the thermal voltage generated by the ITESC, we are able to demonstrate that it is possible to tune the transistor output current over more than two orders of magnitude with a temperature gradient. This is the first demonstration of thermoelectric gating of a transistor, and it is likely to have important applications in smart sensors, human-organic electronic technology interfacing (that is, e-skin), and active flexible electronics. By coupling the electrical conductivity with thermoelectricity, a new field of thermoelectronics is proposed.

Results

Electrolyte-gated transistors

First, the electrical properties of an electrolyte-gated transistor are characterized. Bottom contact, top gate transistors are fabricated using regioregular poly(3-hexylthiophene-2,5-diyl) (P3HT) as the active semiconducting layer and poly(vinylphosphonic acid-co-acrylic acid) (P(VPA-AA)) as the polyanionic electrolyte insulator (Fig. 1a). The P(VPA-AA) phosphonic acid groups are strongly acidic (the first acidic constant, pKa1, is about 2.5±0.5 in water), and therefore provide plenty of potentially mobile cations (ca. 8 mmol g−1, considering one dissociated proton per phosphonic acid group). The anionic phosphonate groups are instead virtually immobile, preventing penetration of anions into the conjugated polymer when a negative gate is applied, and thus precluding electrochemical doping of the bulk semiconducting layer26. When a negative bias voltage is applied to the gate, protons in the electrolyte insulator layer drift towards the electrolyte-metal gate interface, while negative immobile ions accumulate at the electrolyte-semiconductor interface, establishing two EDLs (Helmholtz layer). The charged sheets within these Helmholtz layers are separated by only a few Angstroms, leading to a very large gate capacitance. The typical output characteristics of a P3HT-based electrolyte-gated transistor at four different gate voltages (Vg) are reported in Fig. 1b. The device displays a large gate modulation of the drain current (Ids), in both the linear and saturation regimes, for driving voltages of only a few hundreds of millivolts. The transfer characteristics reported in Fig. 1c, clearly show a large modulation of Ids with on-to-off current ratios typically greater than 104 for Vg range of only 1.5 V, while the threshold voltage (Vth) is −0.18 V. Importantly, drain currents as large as 4 μA (channel length L=10 μm, channel width W=1 mm) are measured at very low gate and drain biases (that is, Vg=Vds=−1.2 V). This low-voltage, high-current operation reflects the very large capacitance of the electrolyte gate dielectric, which induces >1013 carrier cm−2 in the source-drain channel at gate biases of <1 V (see Supplementary Fig.).

Figure 1: Electrical characteristics of an electrolyte-gated transistor.
figure 1

Schematic diagram of an electrolyte-gated transistor and illustration of the channel charge and ion distribution within the electrolyte layer. The chemical structures of P3HT and P(VPA-AA) are also reported (a). Representative output characteristics of the P3HT-based electrolyte-gated transistor (Ti gate metal, L=10 μm, W=1 mm) (b). Corresponding transfer characteristics at Vds=−1.2 V (c).

Ionic thermoelectric voltage generators

As a next step, the thermoelectric properties of the PEO-NaOH electrolyte is investigated using the procedure described before16. When NaOH is added to a low molecular weight PEO (Mw=400 g mol−1), the alcohol end-groups (–COH) transform into negatively charged alkoxide end-groups (–CO Na+). The resulting electrolyte is composed of polymeric anions that are mostly immobile and mobile Na+ cations, as shown in Fig. 2a. The PEO-NaOH solution is then injected into a small cylindrical cavity (1.5 mm thick, diameter of 10 mm), comprising two planar gold electrodes (see ‘Methods’ section for further details). When a temperature different ΔT is applied between the two electrodes, the more mobile Na+ cations diffuse fast towards the cold side, while uncompensated less mobile alkoxylate and carboxylate anions remain at the hot side. This generates a high Soret-induced open voltage between the two electrodes. At each given ΔT, the corresponding thermal voltage can be acquired. In Fig. 2b, the thermovoltage at different ΔT was studied in the temperature range from 15 to 45 °C. For a fixed ΔT, the voltage was measured after the thermovoltage is stabilized for 5 min. The results are presented in Fig. 2c and demonstrate that Vthermal varies linearly with ΔT, exhibiting a remarkable Seebeck coefficient of 7 mV K−1. The switching time of the ITECS is of 25 s and 50 s at 70 and 90% of the response, respectively (Fig. 2d). This Seebeck coefficient is well within the high-performance range reported previously for PEO-NaOH-based ITESC, assuring that devices in this study are representative of the high-performance material. Hence, ionic polymer solutions can provide remarkably high and stable Vthermal over a long period of time, facilitating the function of gating a transistor.

Figure 2: Electrical characteristics of the ionic thermoelectric voltage generators.
figure 2

Schematic diagram of the ITESC. Positive charges are mobile Na+ cations, while negative charges are immobile alkoxylate and carboxylate anions (a). Measured Vthermal and ΔT between the two Au electrodes (b). Linear fitting of Vthermal with different ΔT values. For each point, ΔT is fixed until Vthermal was stable. The slope of the linear fit to the data gives a Seebeck coefficient of 7 mV K−1. (c) The error bar represents the fluctuation of ΔT and Vthermal at each point. Switching characteristics of the device showing a response time of 25 s (50 s) for 70% (90%) of the saturated voltage (d).

Heat-gated transistors

Having characterized the thermoelectric properties of PEO-NaOH and the electrical properties of P3HT-based electrolyte-gated transistors, we combine the two in an ionic thermoelectric-gated transistor. This heat-gated transistor is operated by integrating the two devices in series (details can be found in Supplementary Fig. 2): the working electrode of the thermoelectric generator is connected to the transistor gate electrode, while the second ITESC electrode is connected to the source electrode (grounded). Figure 3a shows the typical output characteristics of a P3HT-based ionic thermoelectric-gated transistors recorded at different ΔT. The drain current is measured after Vthermal stabilizes for each ΔT. As shown in Fig. 3a, a large heat modulation of the drain current, both in the linear and saturation regimes, is observed when ΔT is increased from 31 to −35 K. The output curves show proper saturation at high drain biases with negligible hysteresis. A relatively large on-to-off current ratio of more than two orders of magnitude is extracted from the transfer characteristics reported in Fig. 3b (transfer characteristic curves of different channel length are shown in Supplementary Fig. S3). Compared with the transfer characteristics of the same electrolyte-gated transistor recorded when an external gate bias is applied to the gate (dashed line in Fig. 3b), the variable ΔT produces a similar transfer curve for the ionic thermoelectric-gated transistor. This demonstrates that ionic thermoelectric effect can efficiently be used to gate the transistor. Note that, although the drain current varies in response to ΔT, it can also be used to measure the absolute value of temperature if the temperature at one side of the ITESC is known (details is shown in Supplementary Fig. 4).

Figure 3: Electrical characteristics of the heat-gated transistors.
figure 3

Output characteristics at different fixed gating ΔT (Ti gate, channel length L=2 μm) (a). Transfer characteristics with channel length=2 μm (b). Output current tracking with the variation of ΔT (c). Multi circles operation of the heat-gated transistor (d).

The modulation of the drain current with temperature is also investigated by tracking different ΔT. The temperature of the two electrodes of the ionic thermoelectric generator is switched every 300 s (when Vthermal is stable), and ΔT is increased after every switch. Such a relatively long interval is required to establish a stable ΔT throughout the device, (see details in Supplementary Fig. 5). Figure 3c clearly shows that the drain current follows the variation of Vthermal very closely. Note that the response time of the ionic thermoelectric-gated transistor is not limited by the switching time of the electrolyte-gated transistor, but rather by the response of the thermoelectric component. Indeed, in electrolyte-gated transistors, the EDL at the semiconductor-electrolyte interface forms within only 1–10 ms26,27, while the response time of the ITESC is 25–50 s (see Fig. 2d and Supplementary Fig. 5). The on current is overall remarkably stable over time as observed by operating different cycles at the same ΔT (see Fig. 3d). As the time response of the ITESC decreases with the square root of the length of the thermoelectric leg, faster response can be obtained by decreasing the thickness. However, instabilities in Vthemal needs to be taken into account when reducing the device dimensions as ΔT also decreases. Although our heat-gated transistors do not operate at high frequency, they may find applications in important low-frequency range technology, such as e-skin for health monitoring. Indeed, low-frequency changes in skin temperature typically occur in the range of 0.005–0.05 Hz (that is, 20–200 s). These small skin temperature variations (about 1 K) correlate with tissue blood flow and can function as naturally occurring markers for monitoring periodic contraction and dilation of the vessels, that have diagnostic value for conditions such as congestive heart disease and tissue hypoxia5.

Traditionally, the figure-of-merit that determines the conversion of a modulation in the gate voltage ΔVg to a modulation in the drain current ΔIds, is the transistor’s transconductance. The latter is defined as gmIdsVg and it is the main transistor parameter that governs signal amplification. In a similar fashion, we can define a thermal transconductance (gthermal) for the ionic thermoelectric-gated transistor as gthermalIds/SΔT. The transistor’s transconductance should be maximized at the minimum required gate voltage in order to detect minute electrical potentials and increase sensitivity20. Tuning the electrolyte-gated transistor’s transfer characteristic with its maximum transconductance at zero applied Vg has been accomplished, for example, by simply varying the channel geometry and/or through the use of a different gate electrode material28. As in the case of electrolyte-gated transistors29,30, we found that different gate electrode materials shift the transfer curve in a way that reflects the voltage drop at the gate/electrolyte interface (Fig. 4a). Cu, being a high work function metal electrode (ΦCu=4.3 eV), is the most effective at turning the transistor ON at already zero ΔT (or zero applied Vthermal), while a larger temperature gradient (high Vthermal) needs to be applied to Ti, a low work function electrode (ΦTi=3.8 eV), to achieve the same effect. The transfer characteristic curves for different channel lengths and stability of Cu gate devices are shown is Supplementary Fig. 6. Accordingly, the transconductance extracted for our ionic thermoelectric-gated transistor with Cu as the gate metal is three times larger than that obtained for equivalent Ti-gated transistors (Fig. 4b). This allows for an appreciable detection of current (ΔIds=20 nA) for ΔT as low as 1 K. Note indeed that to get the same increment in Ids with Ti-gated transistors, a ΔT of 3.8 K would be required. On the other hand, Ti-gated transistors possess a much higher on/off ratio in the full temperature range considered here (see Supplementary Fig. 7). The gate electrode materials therefore represent an effective route to tune the thermal voltage at which the high transconductance (or high on/off ratio) is achieved. In addition to changing the gate electrode material, Vthermal can be enhanced through the same strategy used in traditional p-type only thermoelectric generators31, that is, by adding in series thermocouples made of PEO-NaOH leg and a metal (or conducting polymer) leg of vanishingly small Seebeck coefficient.

Figure 4: Effect of gate metal electrode on heat-gated transistors.
figure 4

Comparison of the transfer characteristics of ionic thermoelectric-gated transistors comprising Ti and Cu as the gate electrode (a) and relative transconductance (b).

Heat-gated inverters

A simple logic circuit one could build with an ionic thermoelectric-gated transistor is a resistor-load inverter. Such a circuit is shown in the diagram in the inset of Fig. 5, in which the channel is connected to a battery through a series resistor, across which the output voltage is measured. In this configuration, a change in the temperature gradient applied to the gate is manifested as a voltage drop across the drain resistor. We fabricated a unipolar inverter by connecting our ionic thermoelectric-gated transistor to a 10 MΩ external load. The value of the resistor was selected so that enough current flows through the load to drop most of the supply voltage (VDD) across it (considering Ids=10−5 V at Vg=−1.2 V for channel length L=2 μm, channel width W=1 mm). The temperature gradient-output voltage characteristic (ΔT-Vout) is plotted in Fig. 5b. The output voltage switches from a low state (−1.2 V) to high state (0 V) when the temperature gradient is swept from ΔT=30 to −32 K. The voltage transfer characteristic shows a 1.1 V output swing, which makes use of 92% of the available supply voltage (VDD=−1.2 V). The switching takes place near ΔT=0 K and the inverter is completely switched within only 20 K of ΔT variation, with a maximum gain (dVout/dSΔT) as high as 8 (Fig. 5c). Remarkably, the inverter characteristics closely resemble those obtained by gating the inverter with an external gate bias. The inverter is the most basic element in circuits used to construct amplifiers and logic gates. Our heat-gated inverter’s characteristics comply with circuit design requirements such as wide output swing and proper gain, which may be tailored by choice of the load and driver gate electrode materials, depending on the design specification, in order to realize larger and more complex integrated circuits.

Figure 5: Electrical characteristics of heat-gated inverters.
figure 5

Schematic diagram of the ionic thermoelectric-gated inverters (a). Output voltage response (VoutT and Vout-Vin) of a resistor-loaded inverter based on a heat-gated transistor for VDD=−1.2 V and temperature gradient −32 K<ΔT<30 K or supply input voltage −0.6 V<Vin<0.4 V. The inset shows the related circuit diagram (b). Corresponding signal gain of the inverter for different temperature gradient ΔT and supply input voltage Vin (c).

Discussion

The high ionic Seebeck voltage of the polymer electrolyte is about 100 times larger than the typical Seebeck voltage of electronic thermoelectric materials. This enable the use of one single thermoelectric leg-based device to reach enough voltage to switch the transistor. To reach the same voltage with an electronic thermoelectric material, a thermoelectric module composed of 100 legs would be required. This emphasizes the unique feature of ionic thermoelectric materials: it is possible to couple one thermoelectric leg per transistor and design an array of smart sensing pixel. The resolution and sensitivity of such device can be dramatically enhanced by connecting more legs electrically in series but thermally in parallel.

The miniaturization of the ITESC could allow to reach the same thermoelectric leg density as that of state of the art thermopiles (hundreds to thousands per cm2) to boost the voltage responsivity from 100 to 104 V/W thus reaching the high sensitivity of pyroelectric detectors. Another way to see the impact of replacing the electronic thermoelectric material with the ionic thermoelectric polymer in a thermopile is that the device would lead to the same voltage by decreasing the number of thermocouples and the size of the device by two order of magnitudes. This would enable thermography by arranging tiny thermopiles in a two-dimensional array. Also, the direct coupling of an organic transistor to an ionic thermopile would enable at least a gain in sensitivity by one order of magnitude, as suggested by the gain obtained in our thermoelectric inverter. It should also be noted that the possibility to control charge accumulation in the transistor channel by inducing different ΔT is not feasible with conventional inorganic or polymeric dielectric gate insulators since the gate and drain-source driving voltages are relatively much higher in traditional transistors.

In summary, we develop an ionic thermoelectric-gated organic transistor. Such a transistor converts a modulation in ΔT to a modulation in the drain current ΔI. Since the operating voltage of our electrolyte-gated transistors is of the same order of magnitude as the variation of the thermal voltage generated by the ITESC, we demonstrate that it is possible to tune the transistor output current over more than two orders of magnitude. Note that in principle, the ionic thermoelectric material could also directly replace the electrolyte of the transistor. We demonstrate for the first time that heat signal can act as input for logic circuits, opening up new possibility to couple electrical conductivity with thermoelectricity, in the new field of thermoelectronics.

Although we have only demonstrated the concept of heat sensing by direct physical contact between heat sink and sensor, our concept would also hold for heating through infrared radiation, thus positioning our finding in the field of infrared photonics. In that context, the gating of a low-voltage organic transistor with an ionic thermoelectric device/ionic thermopile (single or multiple thermocouples) combines several unique features for advances in thermography: addressability of a heat-sensing pixel in a two-dimensional array, high sensitivity that could compete with pyroelectric detection, constant signal under illumination. Hence, the ionic thermoelectric-gated transistor is likely to have important applications in thermometry, thermography, smart sensors, human-organic electronic technology interfacing (that is, e-skin) and active flexible electronics.

Methods

Materials

Regioregular poly(3-hexylthiophene) (P3HT, Sigma-Aldrich) was dissolved in 1,2-dichlorobenzene (10 mg ml−1) and filtered with a 0.2 μm polytetrafluoroethylene syringe filter. Poly(vinylphosphonic acid-co-acrylic acid) (P(VPA-AA)) was purchased from Rhodia, and dissolved in a mixture of 1-propanol and deionized water (40 mg ml−1, solvent ratio of 4:1). The polyelectrolyte solution was then filtered with a 0.2 μm nylon syringe filter.

Transistor fabrication

Interdigitated source and drain electrodes (3-nm-thick Ti and 25-nm-thick Au, patterned by photolithography) were prepared on pre-cleaned corning glass substrates. The substrates were cleaned before use by means of deionized water, acetone and isopropanol. The semiconductor layer was spin-coated from warm solution at 2,000 r.p.m. for 30 s, giving a 30-nm-thick film. The films were then annealed at 120 °C for 30 min under nitrogen. The P(VPA-AA) solution was spin-coated at 2,000 r.p.m. for 60 s and dried on a hot plate under vacuum at 120 °C for 120 s, resulting in a film thickness of about 130 nm. Top gate electrode with a thickness of 80 nm were formed by thermal evaporating various metals through a Ni shadow mask (Tecan Ltd.).

TEG fabrication

Two gold thermistors (30 μm width) were patterned on glass substrate by photolithography. A 1-μm-thick Si3N4 layer is deposited by chemical vapour deposition as an insulating layer. Two round gold electrodes were thermally evaporated (10 mm diameter) on the glass substrate to define the active device area. The prepared glass substrates and a PDMS spacing layer (1.5 mm thickness) were treated for 3 min with UV plasma, contacted and baked at 70 °C in oven for 30 min (cavity volume=0.0785, cm3). PEO-NaOH solution (3 wt%) was prepared following the procedure early reported in ref. 16, and injected into the chamber cavity.

Device characterization

The transistors were characterized using a semiconductor parameter analyser (Keithley 4200-SCS). Impedance measurements were carried out with an Alpha high-resolution dielectric analyser (Novocontrol GmbH). A VAC of 0.001 V at a frequency of 1 kHz was applied, while a VDC was swept. The equivalent circuit model used to extract the effective capacitance can be found in ref. 30. A nanovoltmeter (Keithley Instruments, Inc., model 1282 A) was used to measure the thermal voltage of the thermoelectric generator, while a Keithley 2400 was used to measure the resistance of the thermistor simultaneously.

Data availability

The authors declare that the data supporting the findings of this study are available within the paper and its supplementary information files.

Additional information

How to cite this article: Zhao, D. et al. Ionic thermoelectric gating organic transistors. Nat. Commun. 8, 14214 doi: 10.1038/ncomms14214 (2017).

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.